PIC18F14K22-I/SO Microchip Technology, PIC18F14K22-I/SO Datasheet - Page 17
![IC PIC MCU FLASH 512KX16 20-SOIC](/photos/6/64/66480/150-20-soic_sml.jpg)
PIC18F14K22-I/SO
Manufacturer Part Number
PIC18F14K22-I/SO
Description
IC PIC MCU FLASH 512KX16 20-SOIC
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC16F722-ISS.pdf
(8 pages)
2.PIC18LF13K22-ISS.pdf
(388 pages)
3.PIC18LF13K22-ISS.pdf
(12 pages)
4.PIC18LF13K22-ISS.pdf
(36 pages)
5.PIC18F13K22-ISS.pdf
(382 pages)
Specifications of PIC18F14K22-I/SO
Program Memory Type
FLASH
Program Memory Size
16KB (8K x 16)
Package / Case
20-SOIC (7.5mm Width)
Core Processor
PIC
Core Size
8-Bit
Speed
64MHz
Connectivity
I²C, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
17
Eeprom Size
256 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
512 B
Interface Type
I2C, MSSP, SPI, USART
Maximum Clock Frequency
64 MHz
Number Of Programmable I/os
17
Number Of Timers
4
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 12 Channel
A/d Bit Size
10 bit
A/d Channels Available
12
Height
2.05 mm
Length
12.8 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V, 2.7 V
Width
7.5 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F14K22-I/SO
Manufacturer:
Microchip Technology
Quantity:
1 786
Part Number:
PIC18F14K22-I/SO
Manufacturer:
MIC
Quantity:
20 000
4.2.1
The previous programming example assumed that the
device has been Bulk Erased prior to programming
(see Section 4.1.1 “High-Voltage ICSP Bulk Erase”).
It may be the case, however, that the user wishes to
modify only a section of an already programmed
device.
TABLE 4-6:
© 2009 Microchip Technology Inc.
Step 1: Direct access to program Flash.
Step 2: Read program Flash into buffer (Section 5.1 “Read Program Flash, ID Locations and Configuration Bits”).
Step 3: Set the Table Pointer for the block to be erased.
Step 4: Enable memory writes and setup an erase.
Step 5: Initiate erase.
Step 6: Poll WR bit. Repeat until bit is clear.
Step 7: Load write buffer. The correct bytes will be selected based on the Table Pointer.
To continue modifying data, repeat Steps 2 through 6, where the Address Pointer is incremented by the appropriate number of bytes
(see Table 4-4) at each iteration of the loop. The write cycle must be repeated enough times to completely rewrite the contents of the
erase buffer.
Step 8: Disable writes.
Command
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1101
1111
0000
0000
4-bit
•
•
•
MODIFYING PROGRAM FLASH
MODIFYING PROGRAM FLASH
0E <Addr[21:16]>
0E <Addr[21:16]>
0E <Addr[8:15]>
0E <Addr[8:15]>
0E <Addr[7:0]>
0E <Addr[7:0]>
<MSB><LSB>
<MSB><LSB>
<MSB><LSB>
Data Payload
9C A6
8E A6
6E F8
6E F7
6E F6
84 A6
88 A6
88 A6
82 A6
50 A6
6E F5
6E F8
6E F7
6E F6
94 A6
00 00
00 00
00 00
00 00
•
•
•
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
BSF
BSF
NOP
NOP
MOVF
MOVWF
NOP
Shift out data
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
Write 2 bytes and post-increment address by 2.
Repeat as many times as necessary to fill the write buffer
Write 2 bytes and start programming.
NOP - hold PGC high for time P9 and low for time P10.
BCF
Advance Information
EECON1, EEPGD
EECON1, CFGS
EECON1, WREN
<Addr[21:16]>
TBLPTRU
<Addr[8:15]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
EECON1, WREN
EECON1, FREE
<Addr[21:16]>
TBLPTRU
<Addr[8:15]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
EECON1, FREE
EECON1, WR
Erase starts on the 4th clock of this instruction
EECON1, W, 0
TABLAT
PIC18F1XK22/LF1XK22
(1)
The appropriate number of bytes required for the erase
buffer must be read out of program Flash (as described
in Section 5.2 “Verify Program Flash and ID Loca-
tions”) and buffered. Modifications can be made on
this buffer. Then, the block of program Flash that was
read out must be erased and rewritten with the
modified data.
The WREN bit must be set if the WR bit in EECON1 is
used to initiate a write sequence.
Core Instruction
DS41357B-page 17