PIC18F24J10-I/SO Microchip Technology, PIC18F24J10-I/SO Datasheet - Page 155

• Manufacturer Part Number: PIC18F24J10-I/SO
• Description: IC PIC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F24J10-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1024 B
• Interface Type: SPI, I2C, MSSP, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 100 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162074 - HEADER INTRFC MPLAB ICD2 44TQFPAC162067 - HEADER INTRFC MPLAB ICD2 40/28P
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

16.3.3
To enable the serial port, MSSP Enable bit, SSPEN
(SSPxCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, reinitialize the
SSPxCON registers and then set the SSPEN bit. This
configures the SDIx, SDOx, SCKx and SSx pins as
serial port pins. For the pins to behave as the serial port
function, some must have their data direction bits (in
the TRIS register) appropriately programmed as
follows:
• SDIx is automatically controlled by the SPI module
• SDOx must have TRISC<5> (or TRISD<2>) bit
• SCKx (Master mode) must have TRISC<3> (or
• SCKx (Slave mode) must have TRISC<3> (or
• SSx must have TRISA<5> (or TRISD<3>) bit set
FIGURE 16-2:
© 2009 Microchip Technology Inc.
cleared
TRISD<0>) bit cleared
TRISD<0>) bit set
ENABLING SPI I/O
SPI Master SSPM<3:0> = 00xxb
MSb
PROCESSOR 1
Serial Input Buffer
SPI MASTER/SLAVE CONNECTION
Shift Register
(SSPxBUF)
(SSPxSR)
LSb
SDOx
SCKx
SDIx
Serial Clock
PIC18F45J10 FAMILY
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.
16.3.4
Figure 16-2 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCKx signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data – Slave sends dummy data
• Master sends data – Slave sends data
• Master sends dummy data – Slave sends data
SDOx
SCKx
SDIx
TYPICAL CONNECTION
SPI Slave SSPM<3:0> = 010xb
MSb
Serial Input Buffer
Shift Register
(SSPxBUF)
PROCESSOR 2
(SSPxSR)
LSb
DS39682E-page 153