ADE7763ARSZ Analog Devices Inc, ADE7763ARSZ Datasheet - Page 5

• Manufacturer Part Number: ADE7763ARSZ
• Description: IC ENERGY METERING 1PHASE 20SSOP
• Manufacturer: Analog Devices Inc

Specifications of ADE7763ARSZ

• Input Impedance: 390 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 3mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP (0.200", 5.30mm Width)
• Meter Type: Single Phase
• Ic Function: Single-Phase Active And Apparent Energy Metering IC
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: SSOP
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADE7763ZEB - BOARD EVALUATION FOR ADE7763
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TIMING CHARACTERISTICS
AV
Table 2. Timing Characteristics
Parameter
Write Timing
Read Timing
1
2
3
4
5
Sample tested during initial release and after any redesign or process change that could affect this parameter. All input signals are specified with tr = tf = 5 ns (10% to
90%) and timed from a voltage level of 1.6 V.
See Figure 3, Figure 4, and the Serial Interface section.
Minimum time between read command and data read for all registers except waveform register, which is t
Measured with the load circuit in Figure 2 and defined as the time required for the output to cross 0.8 V or 2.4 V.
Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit in Figure 2. The measured number is then extrapolated back
to remove the effects of charging or discharging the 50 pF capacitor. This means that the time quoted in the timing characteristics is the true bus relinquish time of
the part and is independent of the bus loading.
t
t
t
t
t
t
t
t
t
t
t
t
t
DD
1
2
3
4
5
6
7
8
9
10
11
12
13
3
4
5
= DV
SCLK
DOUT
SCLK
DIN
DIN
CS
CS
DD
= 5 V ± 5%, AGND = DGND = 0 V, on-chip reference, CLKIN = 3.579545 MHz XTAL, T
t
t
1
1
1
0
Spec
50
50
50
10
5
400
50
100
4
50
30
100
10
100
10
0
0
t
2
A5
A5
1, 2
t
3
COMMAND BYTE
COMMAND BYTE
A4
A4
t
4
A3
A3
t
5
Unit
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min)
μs min
ns min
ns min
ns max
ns min
ns max
ns min
A2
A2
A1
A1
Figure 3. Serial Write Timing
Figure 4. Serial Read Timing
A0
A0
Rev. B | Page 5 of 56
t
t
7
t
9
11
Test Conditions/Comments
CS falling edge to first SCLK falling edge.
SCLK logic high pulse width.
SCLK logic low pulse width.
Valid data setup time before falling edge of SCLK.
Data hold time after SCLK falling edge.
Minimum time between the end of data byte transfers.
Minimum time between byte transfers during a serial write.
CS hold time after SCLK falling edge.
Minimum time between read command (i.e., a write to communication
register) and data read.
Minimum time between data byte transfers during a multibyte read.
Data access time after SCLK rising edge following a write to the
communication register.
Bus relinquish time after falling edge of SCLK.
Bus relinquish time after rising edge of CS .
DB7
DB7
MOST SIGNIFICANT BYTE
MOST SIGNIFICANT BYTE
9
= 500 ns min.
t
11
DB0
DB0
t
t
7
10
MIN
LEAST SIGNIFICANT BYTE
DB7
LEAST SIGNIFICANT BYTE
DB7
to T
t
6
MAX
= −40°C to +85°C.
t
12
DB0
DB0
t
13
t
ADE7763
8