MCIMX6Q6AVT10AC Freescale Semiconductor, MCIMX6Q6AVT10AC Datasheet - Page 32

• Manufacturer Part Number: MCIMX6Q6AVT10AC
• Description: Processors - Application Specialized i.MX6Q
• Manufacturer: Freescale Semiconductor
• Type: Multimedia Applicationsr

Specifications of MCIMX6Q6AVT10AC

• Rohs: yes
• Core: ARM Cortex A9
• Processor Series: i.MX6
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 1 GHz
• Data Ram Size: 16 KB
• Operating Supply Voltage: 1.05 V to 1.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: FCBGA
• Interface Type: I2C, I2S, UART, USB
• Memory Type: L1/L2 Cache, ROM, SRAM
• Minimum Operating Temperature: - 40 C
• Number Of Timers: 2

Electrical Characteristics
For additional information, see the i.MX 6Dual/6Quad reference manual (IMX6DQRM).
4.3.2
4.3.2.1
The LDO_1P1 regulator implements a programmable linear-regulator function from VDD_HIGH_IN (see
Table 6
to 1.2 V with the nominal default setting as 1.1 V. The LDO_1P1 supplies the USB Phy, LVDS Phy, HDMI
Phy, MIPI Phy, and PLLs. A programmable brown-out detector is included in the regulator that can be used
by the system to determine when the load capability of the regulator is being exceeded to take the
necessary steps. Current-limiting can be enabled to allow for in-rush current requirements during start-up,
if needed. Active-pull-down can also be enabled for systems requiring this feature.
For information on external capacitor requirements for this regulator, see the Hardware Development
Guide for i.MX 6Quad, 6Dual, 6DualLite, 6Solo Families of Applications Processors
(IMX6DQ6SDLHDG).
For additional information, see the i.MX 6Dual/6Quad reference manual (IMX6DQRM).
4.3.2.2
The LDO_2P5 module implements a programmable linear-regulator function from VDD_HIGH_IN (see
Table 6
with the nominal default setting as 2.5 V. The LDO_2P5 supplies the SATA Phy, USB Phy, LVDS Phy,
HDMI Phy, MIPI Phy, E-fuse module and PLLs. A programmable brown-out detector is included in the
regulator that can be used by the system to determine when the load capability of the regulator is being
exceeded, to take the necessary steps. Current-limiting can be enabled to allow for in-rush current
requirements during start-up, if needed. Active-pull-down can also be enabled for systems requiring this
feature. An alternate self-biased low-precision weak-regulator is included that can be enabled for
applications needing to keep the output voltage alive during low-power modes where the main regulator
driver and its associated global bandgap reference module are disabled. The output of the weak-regulator
is not programmable and is a function of the input supply as well as the load current. Typically, with a 3 V
input supply the weak-regulator output is 2.525 V and its output impedance is approximately 40
For information on external capacitor requirements for this regulator, see the Hardware Development
Guide for i.MX 6Quad, 6Dual, 6DualLite, 6Solo Families of Applications Processors
(IMX6DQ6SDLHDG).
For additional information, see the i.MX 6Dual/6Quad reference manual (IMX6DQRM).
32
•
Analog regulation mode. The regulation FET is controlled such that the output voltage of the
regulator equals the programmed target voltage. The target voltage is fully programmable in 25 mV
steps.
for minimum and maximum input requirements). Typical Programming Operating Range is 1.0 V
for min and max input requirements). Typical Programming Operating Range is 2.25 V to 2.75 V
Regulators for Analog Modules
LDO_1P1
LDO_2P5
i.MX 6Dual/6Quad Automotive and Infotainment Applications Processors, Rev. 2
Freescale Semiconductor

.