MAX9271GTJ+T Maxim Integrated, MAX9271GTJ+T Datasheet - Page 30

• Manufacturer Part Number: MAX9271GTJ+T
• Description: Serializers & Deserializers - Serdes 1.5Gbps 16Bit Coax/STP serializer
• Manufacturer: Maxim Integrated
• Type: Serializerr

Specifications of MAX9271GTJ+T

• Rohs: yes
• Data Rate: 1.5 Gbit/s
• Input Type: CMOS/LVCMOS
• Output Type: CML
• Number Of Inputs: 16
• Number Of Outputs: 1
• Operating Supply Voltage: 1.7 V to 3.6 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: TQFN-32
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT

The serializer/deserializer are read using the internally
stored register address as an address pointer, the same
way the stored register address is used as an address
pointer for a write. The pointer autoincrements after each
data byte is read using the same rules as for a write. Thus,
a read is initiated by first configuring the register address
by performing a write
read consecutive bytes from the device, with the first data
byte being read from the register address pointed by
the previously written register address. Once the master
sends a NACK, the device stops sending valid data.
The serializer supports I
eral on the remote side of the communication link using
SCL clock stretching. While multiple masters can reside
on either side of the communication link, arbitration is
not provided. The connected masters need to support
SCL clock stretching and provide contention detection.
The remote side I
ing to the local-side I
bit rates can be found in
(register 0x0D) to set the remote I
Figure 30. Format for I
Table 4. I
Maxim Integrated
REPEATED START
I
20kbps > f > 50kbps
2
LOCAL BIT RATE
C Communication with Remote-Side Devices
S
S
f > 50kbps
f < 20kbps
2
C Bit-Rate Ranges
1
1
2
C bit-rate range must be set accord-
2
0
0
C Read
2
C bit rate. Supported remote-side
(Figure
2
0
0
C communication with a periph-
ADDRESS = 0x80
ADDRESS = 0x81
Table
0
0
30). The master can now
0
0
4. Set the I2CMSTBT
2
16-Bit GMSL Serializer with Coax or
C bit rate. If using a
Format for Reading
0
0
REMOTE BIT-RATE RANGE
0
0
0 = WRITE
1 = READ
0
1
Up to 400kbps
Up to 10kbps
Up to 1Mbps
A
A
D7
0
bit rate different than 400kbps, local- and remote-side
I
the SLV_SH register settings on both sides.
The serializer supports I
two device addresses. Use address translation to assign
unique device addresses to peripherals with limited
I
from) are stored in registers 0x09 and 0x0B. Destination
addresses (address to translate to) are stored in registers
0x0A and 0x0C.
The serializer supports broadcast commands to control
multiple peripheral devices. Select an unused device
address to use as a broadcast device address. Program
the remote-side GMSL device to translate the broadcast
device address (source address stored in registers 0x09,
0x0B) to the peripheral device address (destination
address stored in registers 0x0A, 0x0C). Any commands
sent to the broadcast address are sent to all designated
peripherals, while commands sent to a peripheral’s unique
device address are sent to that particular device only.
2
2
C addresses. Source addresses (address to translate
C setup and hold times should be adjusted by setting
D6
0
REGISTER ADDRESS = 0x00
REGISTER 0x00 READ DATA
D5
0
D4
0
D3
0
STP Cable Drive
D2
0
2
C address translation for up to
D1
I
0
2
I2CMSTBT SETTING
C Address Translation
D0
0
I
2
Up to 110
C Broadcast Mode
MAX9271
A
N
Any
000
P
S = START BIT
P = STOP BIT
A = ACK
N = NACK
D_ = DATA BIT
30