ZL30105_05 ZARLINK [Zarlink Semiconductor Inc], ZL30105_05 Datasheet - Page 16
ZL30105_05
Manufacturer Part Number
ZL30105_05
Description
T1/E1/SDH Stratum 3 Redundant System Clock Synchronizer for AdvancedTC TM and H.110
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.ZL30105_05.pdf
(52 pages)
- Current page: 16 of 52
- Download datasheet (2Mb)
The delay value can be reset by setting the TIE Corrector Circuit Clear pin (TIE_CLR) low for at least 15 ns. This
results in a phase alignment between the input reference signal and the output clocks and frame pulses as shown
in Figure 26. The speed of the phase alignment correction is limited by the selected loop filter bandwidth and the
phase slope limit (see Table 2). Convergence is always in the direction of least phase travel. TIE_CLR can be kept
low continuously; in that case the output clocks will always align with the selected input reference. This is illustrated
in Figure 9.
The Hitless Mode Switching (HMS) pin enables phase hitless returns from Freerun and Holdover modes to Normal
mode in a single reference operation. A logic low at the HMS input disables the TIE circuit updating the delay value
thereby forcing the output of the PLL to gradually move back to the original point before it went into Holdover mode.
(see Figure 10). This prevents accumulation of phase in network elements. A logic high (HMS=1) enables the TIE
circuit to update its delay value thereby preventing a large output phase movement after return to Normal mode.
This causes accumulation of phase in network elements. In both cases the PLL’s output can be aligned with the
input reference by setting TIE_CLR low. Regardless of the HMS pin state, reference switching in the ZL30105 is
always hitless unless TIE_CLR is kept low continuously.
REF1
REF1
REF0
REF0
Output
Clock
Output
Clock
locked to REF1
locked to REF0
TIE_CLR = 0
Figure 9 - Timing Diagram of Hitless Reference Switching
Zarlink Semiconductor Inc.
ZL30105
16
REF0
REF1
REF0
REF1
Output
Clock
Output
Clock
locked to REF1
locked to REF0
TIE_CLR = 1
Data Sheet
Related parts for ZL30105_05
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: