hdmp-1526 ETC-unknow, hdmp-1526 Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
hdmp-1526
Manufacturer Part Number
hdmp-1526
Description
Fibre Channel Transceiver Chip
Manufacturer
ETC-unknow
Datasheet
1.HDMP-1526.pdf
(14 pages)
parallel data (see Figure 3). This
clock is multiplied by 10 to
generate the 1062.5 MHz clock
necessary for the high-speed
serial outputs.
FRAME MUX
The FRAME MUX accepts the 10-
bit wide parallel data from the
INPUT LATCH. Using internally
generated high-speed clocks, this
parallel data is multiplexed into
the 1062.5 MBd serial data
stream. The data bits are
transmitted sequentially, from the
least significant bit (TX[0]) to the
most significant bit (TX[9]).
OUTPUT SELECT
The OUTPUT SELECT block
provides for an optional internal
loopback of the high-speed serial
signal, for testing purposes.
In normal operation, LOOPEN is
set low and the serial data stream
is placed at
mode is activated by setting
LOOPEN high, the
are held static and the serial
output signal is internally
wrapped to the INPUT SELECT
box of the receiver section.
INPUT SELECT
The INPUT SELECT block
determines whether the signal at
serial signal is used. In normal
operation, LOOPEN is set low
and the serial data is accepted at
high, the high-speed serial signal
is internally looped-back from the
transmitter section to the receiver
section. This feature allows for
loop-back testing exclusive of the
transmission medium.
684
DIN or the internal loop-back
DIN. When LOOPEN is set
DOUT. When wrap-
DOUT pins
RX PLL/CLOCK RECOVERY
The RX PLL/CLOCK RECOVERY
block is responsible for frequency
and phase locking onto incoming
serial data stream and recovering
the bit and byte clocks.
In order to accomplish this, upon
startup, the user should set
-LCKREF low for a period of at
least 500 sec. This allows the
PLL to first frequency lock onto
the 106.25 MHz reference clock
provided at the REFCLK input.
The RX PLL/CLOCK RECOVERY
circuitry multiplies this reference
clock by 10 to generate an
internal 1062.5 MHz clock. After
500 sec, the user should set
-LCKREF high. This will allow the
receiver to frequency and phase
lock the internal 1062.5 MHz
clock onto the incoming serial
data stream. Once locked, the
receiver will recover the two
53.125 MHz receiver byte clocks
(RBC1/RBC0). These byte clocks
are approximately 180 out of
phase with each other and are
alternately used to clock the
10-bit parallel output data.
INPUT SAMPLER
The INPUT SAMPLER is
responsible for converting the
serial input signal into a retimed
serial bit stream. In order to
accomplish this, it uses the high
speed serial clock recovered from
the RX PLL/CLOCK RECOVERY
block. This serial bit stream is
sent to the FRAME DEMUX and
BYTE SYNC block.
FRAME DEMUX AND BYTE
SYNC
The FRAME DEMUX AND BYTE
SYNC block is responsible for
restoring the 10-bit parallel data
from the high speed serial bit
stream. This block is also
responsible for recognizing the
comma character (or a K28.5
character) of positive disparity
(0011111xxx). When recognized,
the FRAME DEMUX AND BYTE
SYNC block works with the RX
PLL/CLOCK RECOVERY block to
properly align the receive byte
clocks to the parallel data. When
a comma character is detected
and realignment of the receiver
byte clocks (RBC1/RBC0) is
necessary, these clocks are
stretched, not slivered, to the
next possible correct alignment
position. These clocks will be
fully aligned by the start of the
second 4-byte ordered set. The
second comma character received
shall be aligned with the rising
edge of RBC1. Comma characters
should not be transmitted in
consecutive succession to allow
the receiver byte clocks to
maintain their proper recovered
frequencies.
OUTPUT DRIVERS
The OUTPUT DRIVERS present
the 10-bit parallel recovered data
byte properly aligned to the
receive byte clocks (RBC1/
RBC0), as shown in Figure 4.
These output data buffers provide
TTL compatible signals.