at43usb320a ATMEL Corporation, at43usb320a Datasheet - Page 94
at43usb320a
Manufacturer Part Number
at43usb320a
Description
Full-speed Usb Microcontroller With An Embedded Hub
Manufacturer
ATMEL Corporation
Datasheet
1.AT43USB320A.pdf
(115 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 94 of 115
- Download datasheet (2Mb)
94
AT43USB320A
Hub Port Status Change Register – PSCR1..3
The microcontroller firmware uses the bits in this register to monitor when a port status change
has occurred, which then gets reported to the host through the Port Change Field
wPortChange .
Except for bit 3, the Port Overcurrent Indicator Change, the bits in this register are set by the
USB hardware. Otherwise, the firmware should only clear these bits.
• Bit 7..5 – Reserved
These bits are reserved in the AT43USB320A and will read as zero.
• Bit 4 – RSTSC: Port Reset Status Change
0 = No change
1 = Reset complete
This bit is set by the USB hardware after it completes RESET signaling which is initiated when
the Reset and Enable Port command is detected at the Port Control Register, HPCON. The
firmware sends this command when it decodes a SetPortFeature(PORT_RESET) request
from the host.
At EOF2 after the hardware completes the port reset, the hardware sets the Port Enable Sta-
tus bit and clears the Port Reset Status bit of the Hub Port Status Register, HPSTAT. Cleared
by firmware, ClearPortFeature(PORT_RESET).
• Bit 3 – POCIC: Port Overcurrent Indicator Change
0 = No change has occurred on Overcurrent Indicator
1 = Overcurrent Indicator has changed
This bit is relevant to hubs with individual overcurrent reporting only. The firmware sets this bit
as a result of detecting overcurrent at the ports OVC# pin. The firmware clears bit through
ClearPortFeature(PORT_OVER_CURRENT). For Port 1, this bit is always cleared.
• Bit 2 – PSSC: Port Suspend Status Change
0 = No change
1 = Resume completed
Port 1:4 is set by hardware upon completion of firmware initiated resume process. Port 5 is set
by firmware 20 ms after the next EOF2 after completion of resume process. RESUME signal-
ing is initiated through global resume, selective resume and remote wakeup. Cleared by
firmware via host request ClearPortFeature(PORT_SUSPEND).
Port1 $1FB0
Port2 $1FB1
Port3 $1FB2
Port4 $1FB3
Port5 $1FB4
Read/Write
Initial Value
Bit
7
–
–
–
–
–
R
0
R
6
–
–
–
–
–
0
R
5
–
–
–
–
–
0
RSTSC
RSTSC
RSTSC
RSTSC
RSTSC
R
4
0
POCIC
POCIC
POCIC
POCIC
POCIC
R
3
0
PSSC
PSSC
PSSC
PSSC
PSSC
R
2
0
PESC
PESC
PESC
PESC
PESC
R
1
0
PCSC
PCSC
PCSC
PCSC
PCSC
R
0
0
1443E–USB–4/04
PSCR1
PSCR2
PSCR3
PSCR4
PSCR5
Related parts for at43usb320a
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: