AD7853 Analog Devices, AD7853 Datasheet - Page 15

• Manufacturer Part Number: AD7853
• Description: 3 V to 5 V Single Supply, 200 kSPS, 12-Bit, Serial Sampling ADC
• Manufacturer: Analog Devices

Specifications of AD7853

• Resolution (bits): 12bit
• # Chan: 1
• Sample Rate: 200kSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Uni,SE-Uni
• Ain Range: (Vref) p-p,Uni (Vref)
• Adc Architecture: SAR
• Pkg Type: DIP,SOIC

REV. B
TYPICAL CONNECTION DIAGRAM
Figure 10 shows a typical connection diagram for the AD7853/
AD7853L. The DIN line is tied to DGND so that no data is
written to the part. The AGND and the DGND pins are con-
nected together at the device for good noise suppression. The
CAL pin has a 0.01 F capacitor to enable an automatic self-
calibration on power-up. The SCLK and SYNC are configured
as outputs by having SM1 and SM2 at DV
result is output in a 16-bit word with four leading zeros followed
by the MSB of the 12-bit result. Note that after the AV
DV
the internal reference to settle and for the automatic calibration
on power-up to be completed.
For applications where power consumption is a major concern,
the SLEEP pin can be connected to DGND. See Power-Down
section for more detail on low power applications.
ANALOG INPUT
The equivalent circuit of the analog input section is shown in
Figure 11. During the acquisition interval the switches are both
in the track position and the AIN(+) charges the 20 pF capaci-
tor through the 125
switches SW1 and SW2 go into the hold position retaining
charge on the 20 pF capacitor as a sample of the signal on
AIN(+). The AIN(–) is connected to the 20 pF capacitor, and
this unbalances the voltage at Node A at the input of the com-
parator. The capacitor DAC adjusts during the remainder of the
conversion cycle to restore the voltage at Node A to the correct
value. This action transfers a charge, representing the analog
input signal, to the capacitor DAC which in turn forms a digital
representation of the analog input signal. The voltage on the
AIN(–) pin directly influences the charge transferred to the
capacitor DAC at the hold instant. If this voltage changes dur-
ing the conversion period, the DAC representation of the analog
input voltage will be altered. Therefore it is most important that
the voltage on the AIN(–) pin remains constant during the con-
version period. Furthermore, it is recommended that the AIN(–)
pin is always connected to AGND or to a fixed dc voltage.
Acquisition Time
The track and hold amplifier enters its tracking mode on the
falling edge of the BUSY signal. The time required for the track
and hold amplifier to acquire an input signal will depend on
how quickly the 20 pF input capacitance is charged. The acqui-
sition time is calculated using the formula:
where R
20 pF is the input R, C.
t
ACQ
DD
AIN(+)
AIN(–)
C
REF2
power-up, the part will require approximately 150 ms for
= 9
IN
Figure 11. Analog Input Equivalent Circuit
is the source impedance of the input signal, and 125 ,
(R
125
125
IN
+ 125 )
resistance. On the rising edge of CONVST
TRACK
HOLD
SW1
TRACK
20 pF
NODE A
20pF
SW2
HOLD
DD
. The conversion
CAPACITOR
COMPARATOR
DAC
DD
and
–15–
DC/AC Applications
For dc applications high source impedances are acceptable,
provided there is enough acquisition time between conversions
to charge the 20 pF capacitor. The acquisition time can be
calculated from the above formula for different source imped-
ances. For example with R
time will be 922 ns.
For ac applications, removing high frequency components from
the analog input signal is recommended by use of an RC low-
pass filter on the AIN(+) pin, as shown in Figure 13. In applica-
tions where harmonic distortion and signal to noise ratio are
critical, the analog input should be driven from a low impedance
source. Large source impedances will significantly affect the ac
performance of the ADC. This may necessitate the use of an
input buffer amplifier. The choice of the op amp will be a func-
tion of the particular application.
When no amplifier is used to drive the analog input the source
impedance should be limited to low values. The maximum
source impedance will depend on the amount of total harmonic
distortion (THD) that can be tolerated. The THD will increase
as the source impedance increases and performance will degrade.
Figure 12 shows a graph of the Total Harmonic Distortion vs.
analog input signal frequency for different source impedances.
With the setup as in Figure 13, the THD is at the –90 dB level.
With a source impedance of 1 k and no capacitor on the AIN(+)
pin, the THD increases with frequency.
In a single supply application (both 3 V and 5 V), the V+ and
V– of the op amp can be taken directly from the supplies to the
AD7853/AD7853L which eliminates the need for extra external
power supplies. When operating with rail-to-rail inputs and
outputs at frequencies greater than 10 kHz, care must be taken
in selecting the particular op amp for the application. In particu-
lar, for single supply applications the input amplifiers should be
connected in a gain of –1 arrangement to get the optimum per-
formance. Figure 13 shows the arrangement for a single supply
application with a 50
quency 320 kHz) on the AIN(+) pin. Note that the 10 nF is a
capacitor with good linearity to ensure good ac performance.
Recommended single supply op amps are the AD820 and the
AD820-3 V.
–72
–76
–80
–84
–88
–92
Figure 12. THD vs. Analog Input Frequency
0
THD VS. FREQUENCY FOR DIFFERENT
SOURCE IMPEDANCES
20
INPUT FREQUENCY – kHz
and 10 nF low-pass filter (cutoff fre-
R
IN
IN
= 1k
40
= 5 k , the required acquisition
AD7853/AD7853L
60
R
AS IN FIGURE 13
IN
= 50 , 10nF
80
100