SC16C852LIB,157 NXP Semiconductors, SC16C852LIB,157 Datasheet - Page 28

• Manufacturer Part Number: SC16C852LIB,157
• Description: IC UART DUAL W/FIFO 48-LQFP
• Manufacturer: NXP Semiconductors

Specifications of SC16C852LIB,157

• Features: Programmable
• Number Of Channels: 2, DUART
• Fifo's: 128 Byte
• Protocol: RS485
• Voltage - Supply: 1.8V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935283098157; SC16C852LIB; SC16C852LIB

NXP Semiconductors
SC16C852L
Product data sheet
7.3.1.1 Mode 0 (FCR bit 3 = 0)
7.3.1.2 Mode 1 (FCR bit 3 = 1)
7.3.1 DMA mode
7.3.2 FIFO mode
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger
levels, and select the DMA mode.
In this mode, Transmit Ready (TXRDY) will go to a logic 0 whenever the FIFO (THR, if
FIFO is not enabled) is empty. Receive Ready (RXRDY) will go to a logic 0 whenever the
Receive Holding Register (RHR) is loaded with a character.
In this mode, the Transmit Ready (TXRDY) is set when the transmit FIFO is below the
programmed trigger level. The Receive Ready (RXRDY) is set when the receive FIFO fills
to the programmed trigger level. However, the FIFO continues to fill regardless of the
programmed level until the FIFO is full. RXRDY remains a logic 0 as long as the FIFO fill
level is above the programmed trigger level.
Table 12.
Bit
5:4
3
7:6
Symbol
FCR[7:6]
FCR[5:4]
FCR[3]
FIFO Control Register bits description
All information provided in this document is subject to legal disclaimers.
Description
Receive trigger level in 32-byte FIFO mode
These bits are used to set the trigger levels for receive FIFO interrupt and
flow control. The SC16C852L will issue a receive ready interrupt when the
number of characters in the receive FIFO reaches the selected trigger level.
Refer to
Transmit trigger level in 32-byte FIFO mode
These bits are used to set the trigger level for the transmit FIFO interrupt and
flow control. The SC16C852L will issue a transmit empty interrupt when the
number of characters in FIFO drops below the selected trigger level. Refer to
Table
DMA mode select.
Transmit operation in mode ‘0’: When the SC16C852L is in the non-FIFO
mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode (FIFOs
enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there are no
characters in the transmit FIFO, the TXRDYA/TXRDYB pin will be a logic 0.
Once active, the TXRDYA/TXRDYB pin will go to a logic 1 after the first
character is loaded into the transmit holding register.
Receive operation in mode ‘0’: When the SC16C852L is in non-FIFO
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and there is
at least one character in the receive FIFO, the RXRDYA/RXRDYB pin will be
a logic 0. Once active, the RXRDYA/RXRDYB pin will go to a logic 1 when
there are no more characters in the receiver.
1.8 V dual UART with 128-byte FIFOs and IrDA encoder/decoder
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Rev. 4 — 1 February 2011
14.
Table
13.
[1]
[2]
.
.
SC16C852L
© NXP B.V. 2011. All rights reserved.
28 of 64