SC16C754BIBM,151 NXP Semiconductors, SC16C754BIBM,151 Datasheet - Page 32

• Manufacturer Part Number: SC16C754BIBM,151
• Description: IC UART QUAD W/FIFO 64-LQFP
• Manufacturer: NXP Semiconductors

Specifications of SC16C754BIBM,151

• Number Of Channels: 4, QUART
• Package / Case: 64-LQFP
• Fifo's: 64 Byte
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 5 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.25 V
• Supply Current: 6 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 2.5 V or 3.3 V or 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-3290; 935279069151; SC16C754BIBM-S

NXP Semiconductors
SC16C754B_4
Product data sheet
7.12 Transmission Control Register (TCR)
7.13 Trigger Level Register (TLR)
7.14 FIFO Ready register (FIFO Rdy)
This 8-bit register is used to store the RX FIFO threshold levels to stop/start transmission
during hardware/software flow control.
settings.
Table 20.
TCR trigger levels are available from 0 to 60 bytes with a granularity of four.
Remark: TCR can only be written to when EFR[4] = 1 and MCR[6] = 1. The programmer
must program the TCR such that TCR[3:0] > TCR[7:4]. There is no built-in hardware
check to make sure this condition is met. Also, the TCR must be programmed with this
condition before auto-RTS or software flow control is enabled to avoid spurious operation
of the device.
This 8-bit register is used to store the transmit and received FIFO trigger levels used for
DMA and interrupt generation. Trigger levels from 4 to 60 can be programmed with a
granularity of 4.
Table 21.
Remark: TLR can only be written to when EFR[4] = 1 and MCR[6] = 1. If TLR[3:0] or
TLR[7:4] are logic 0, the selectable trigger levels via the FIFO Control Register (FCR) are
used for the transmit and receive FIFO trigger levels. Trigger levels from 4 to 60 bytes are
available with a granularity of four. The TLR should be programmed for
desired trigger level.
The FIFO Rdy register provides real-time status of the transmit and receive FIFOs of both
channels.
Table 22.
Bit
7:4
3:0
Bit
7:4
3:0
Bit
7:4
3:0
Symbol
TCR[7:4]
TCR[3:0]
Symbol
TLR[7:4]
TLR[3:0]
Symbol
FIFO Rdy[7:4]
FIFO Rdy[3:0]
Transmission control register bits description
Trigger level register bits description
FIFO ready register bits description
Table 21
Description
RX FIFO trigger level to resume transmission [(0 to 60) bytes].
RX FIFO trigger level to halt transmission [(0 to 60) bytes].
Description
RX FIFO trigger levels (4 to 60), number of characters available.
TX FIFO trigger levels (4 to 60), number of spaces available.
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
Rev. 04 — 6 October 2008
Description
0 = there are less than a RX trigger level number of characters in the
RX FIFO
1 = the RX FIFO has more than a RX trigger level number of characters
available for reading or a time-out condition has occurred
0 = there are less than a TX trigger level number of spaces available in
the TX FIFO
1 = there are at least a TX trigger level number of spaces available in the
TX FIFO
shows trigger level register bit settings.
Table 20
shows transmission control register bit
SC16C754B
N
© NXP B.V. 2008. All rights reserved.
4
, where N is the
32 of 51