PIC18F452-I/P Microchip Technology Inc., PIC18F452-I/P Datasheet - Page 25

no-image

PIC18F452-I/P

Manufacturer Part Number
PIC18F452-I/P
Description
40 PIN, 32 KB FLASH, 1536 RAM, 34 I/O
Manufacturer
Microchip Technology Inc.
Datasheet

Specifications of PIC18F452-I/P

A/d Inputs
8-Channel, 10-Bit
Comparators
2
Cpu Speed
10 MIPS
Eeprom Memory
256 Bytes
Input Output
36
Interface
I2C/SPI/USART
Memory Type
Flash
Number Of Bits
8
Package Type
40-pin PDIP
Programmable Memory
32K Bytes
Ram Size
1.5K Bytes
Speed
40 MHz
Timers
1-8-bit, 3-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part Electrostatic Device

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F452-I/P
Manufacturer:
NXP
Quantity:
650
Part Number:
PIC18F452-I/P
Manufacturer:
MICROCHI
Quantity:
100
Part Number:
PIC18F452-I/P
Manufacturer:
MIC
Quantity:
11 200
Part Number:
PIC18F452-I/P
Manufacturer:
MICROCHIP
Quantity:
18
Part Number:
PIC18F452-I/P
Manufacturer:
MICROCHIP
Quantity:
732
Part Number:
PIC18F452-I/P
Manufacturer:
MICROCHIP
Quantity:
620
Part Number:
PIC18F452-I/P
Manufacturer:
XILINX
0
Part Number:
PIC18F452-I/P
Manufacturer:
MIC
Quantity:
20 000
Part Number:
PIC18F452-I/PT
Manufacturer:
EPSON
Quantity:
100
Part Number:
PIC18F452-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC18F452-I/PT
Manufacturer:
MICROCH
Quantity:
20 000
Company:
Part Number:
PIC18F452-I/PT
Quantity:
5 000
2.0
2.1
PIC18F2420/2520/4420/4520 devices can be operated
in ten different oscillator modes. The user can program
the configuration bits, FOSC3:FOSC0, in Configuration
Register 1H to select one of these ten modes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. ECIO
2.2
In XT, LP, HS or HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-1 shows
the pin connections.
The oscillator design requires the use of a parallel cut
crystal.
 2004 Microchip Technology Inc.
Note:
LP
XT
HS
HSPLL High-Speed Crystal/Resonator
RC
RCIO
INTIO1 Internal Oscillator with F
INTIO2 Internal Oscillator with I/O on RA6
EC
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturer’s
specifications.
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
with PLL enabled
External Resistor/Capacitor with
F
External Resistor/Capacitor with I/O
on RA6
on RA6 and I/O on RA7
and RA7
External Clock with F
External Clock with I/O on RA6
OSC
/4 output on RA6
OSC
OSC
/4 output
/4 output
PIC18F2420/2520/4420/4520
Preliminary
FIGURE 2-1:
TABLE 2-1:
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following Table 2-2 for additional
information.
Note 1: See Table 2-1 and Table 2-2 for initial values of
DD
Note:
Mode
XT
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
(1)
(1)
Typical Capacitor Values Used:
C1 and C2.
strip cut crystals.
When using resonators with frequencies
above 3.5 MHz, the use of HS mode,
rather than XT mode, is recommended.
HS mode may be used at any V
which the controller is rated. If HS is
selected, it is possible that the gain of the
oscillator will overdrive the resonator.
Therefore, a series resistor should be
placed between the OSC2 pin and the
resonator. As a good starting point, the
recommended value of R
F
3.58 MHz
4.19 MHz
XTAL
R
varies with the oscillator mode chosen.
4 MHz
4 MHz
S
Freq
(2)
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
CRYSTAL/CERAMIC
RESONATOR OPERATION
(XT, LP, HS OR HSPLL
CONFIGURATION)
S
OSC1
) may be required for AT
15 pF
15 pF
30 pF
50 pF
R
F
(3)
DS39631A-page 23
S
PIC18FXXXX
is 330 .
Sleep
To
OSC2
Internal
Logic
15 pF
15 pF
30 pF
50 pF
DD
for

Related parts for PIC18F452-I/P