MSC8126MP8000 Freescale Semiconductor, MSC8126MP8000 Datasheet - Page 15

• Manufacturer Part Number: MSC8126MP8000
• Description: DSP 16BIT 500MHZ MULTI 431FCPBGA
• Manufacturer: Freescale Semiconductor
• Series: MSC81xx StarCorer
• Type: SC140 Corer

Specifications of MSC8126MP8000

• Interface: DSI, Ethernet, RS-232
• Clock Rate: 500MHz
• Non-volatile Memory: External
• On-chip Ram: 1.436MB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: 0°C ~ 90°C
• Mounting Type: Surface Mount
• Package / Case: 431-FCPBGA
• For Use With: MSC8126ADSE - KIT ADVANCED DEV SYSTEM 8126
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

2.4
This section describes the DC electrical characteristics for the MSC8126. The measurements in Table 5 assume the
following system conditions:
Note: The leakage current is measured for nominal
Freescale Semiconductor
Input high voltage
Input low voltage
CLKIN input high voltage
CLKIN input low voltage
Input leakage current, V
Tri-state (high impedance off state) leakage current, V
Signal low input current, V
Signal high input current, V
Output high voltage, I
except open drain pins
Output low voltage, I
V
Internal supply current:
•
•
Typical power 400 MHz at 1.2 V
Notes:
CCSYN
Wait mode
Stop mode
•
•
•
•
PLL supply current
T
V
— 400 MHz = 1.14–1.26 V
— 500 MHz = 1.16–1.24 V
V
GND
1.
2.
3.
4.
DD
DDH
A
= 25 °C
DC Electrical Characteristics
=
See Figure 5 for undershoot and overshoot voltages.
Not tested. Guaranteed by design.
Measured for 1.2 V core at 25°C junction temperature.
The typical power values were measured using an EFR code with the device running at a junction temperature of 25°C. No
peripherals were enabled and the ICache was not enabled. The source code was optimized to use all the ALUs and AGUs and
all four cores. It was created using CodeWarrior
application dependent and varies widely. To assure proper board design with regard to thermal dissipation and maintaining
proper operating temperatures, evaluate power consumption for your application and use the design guidelines in Chapter 4 of
this document and in MSC8102, MSC8122, and MSC8126 Thermal Management Design Guidelines (AN2601).
= 0 V
= 3.3 V ± 5% V
1
1
, all inputs except CLKIN
OL
OH
DC
= 3.2 mA
Characteristic
IN
= –2 mA,
IL
= V
IH
= 0.8 V
= 2.0 V
DDH
4
MSC8126 Quad Digital Signal Processor Data Sheet, Rev. 15
2
DC
2
DC
DC
Table 5. DC Electrical Characteristics
IN
= V
DDH
®
2.5. These values are provided as examples only. Power consumption is
V
DDH
Symbol
I
VCCSYN
I
V
V
V
I
V
DDW
V
I
DDS
V
I
OZ
I
IHC
I
P
and
ILC
IN
OH
H
OL
L
IH
IL
V
DD
.
GND
GND
Min
–1.0
–1.0
–1.0
–1.0
2.0
2.4
2.0
—
—
—
—
—
Typical
375
290
0.09
0.09
0.09
0.09
1.15
3.0
3.0
—
0
0
0
2
3
3
Electrical Characteristics
3.465
3.465
Max
0.8
0.8
0.4
—
—
—
—
1
1
1
1
4
Unit
mA
mA
mA
µA
µA
µA
µA
W
V
V
V
V
V
V
15