LTC2408CG#TR Linear Technology, LTC2408CG#TR Datasheet - Page 5

• Manufacturer Part Number: LTC2408CG#TR
• Description: IC ADC 24BIT 8CH MICROPWR 28SSOP
• Manufacturer: Linear Technology

Specifications of LTC2408CG#TR

• Number Of Bits: 24
• Sampling Rate (per Second): 7.5
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP (0.200", 5.30mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

TI I G CHARACTERISTICS
otherwise specifications are at T
SYMBOL
f
t
t
t
f
D
f
t
t
t
t
t
t
t
t
t
t
Note 1: Absolute Maximum Ratings are those values beyond which the
life of the device may be impaired.
Note 2: All voltage values are with respect to GND.
Note 3: V
is 0 .
Note 4: Internal Conversion Clock source with the F
to GND or to V
f
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from
a straight line passing through the actual endpoints of the transfer
curve. The deviation is measured from the center of the quantization
band.
Note 7: F
(external oscillator).
Note 8: F
(external oscillator).
Note 9: The converter is in external SCK mode of operation such that
the SCK pin is used as digital input. The frequency of the clock signal
driving SCK during the data output is f
t
t
EOSC
HEO
LEO
CONV
ISCK
ESCK
LESCK
HESCK
DOUT_ISCK
DOUT_ESCK
1
2
3
4
KQMAX
KQMIN
EOSC
5
6
ISCK
W
= 153600Hz unless otherwise specified.
O
O
U
CC
= 0V (internal oscillator) or f
= V
= 2.7 to 5.5V unless otherwise specified, source input
CC
CC
PARAMETER
External Oscillator Frequency Range
External Oscillator High Period
External Oscillator Low Period
Conversion Time
Internal SCK Frequency
Internal SCK Duty Cycle
External SCK Frequency Range
External SCK Low Period
External SCK High Period
Internal SCK 32-Bit Data Output Time
External SCK 32-Bit Data Output Time
CS to SDO Low Z
CS to SDO High Z
CS to SCK
CS to SCK
SCK
SDO Hold After SCK
SCK Set-Up Before CS
SCK Hold After CS
(internal oscillator) or f
or to external conversion clock source with
to SDO Valid
A
= 25 C. (Note 3)
ESCK
EOSC
EOSC
and is expressed in kHz.
= 153600Hz 2%
= 128000Hz 2%
O
pin tied
The
CONDITIONS
F
F
External Oscillator (Note 11)
Internal Oscillator (Note 10)
External Oscillator (Notes 10, 11)
(Note 10)
(Note 9)
(Note 9)
(Note 9)
Internal Oscillator (Notes 10, 12)
External Oscillator (Notes 10, 11)
(Note 9)
(Note 10)
(Note 9)
(Note 5)
O
O
= 0V
= V
denotes specifications which apply over the full operating temperature range,
CC
Note 10: The converter is in internal SCK mode of operation such that
the SCK pin is used as digital output. In this mode of operation the
SCK pin has a total equivalent load capacitance C
Note 11: The external oscillator is connected to the F
oscillator frequency, f
Note 12: The converter uses the internal oscillator.
F
Note 13: The output noise includes the contribution of the internal
calibration operations.
Note 14: For reference voltage values V
of – 0.125 • V
rating of the Analog Input Voltage pin (Pin 3). For 2.5V < V
0.267V + 0.89 • V
For 0.267V + 0.89 • V
to V
Note 15: V
applied to the MUX output.
O
= 0V or F
CC
+ 0.3V.
S
O
is the voltage applied to a channel input. V
REF
= V
CC
to 1.125 • V
CC
.
the input voltage range is – 0.3V to 1.125 • V
CC
EOSC
< V
, is expressed in kHz.
REF
130.66
156.80
REF
LTC2404/LTC2408
2.56
1.64
MIN
250
250
0.5
0.5
45
50
15
50
0
0
0
is limited by the absolute maximum
V
20480/f
CC
256/f
32/f
the input voltage range is – 0.3V
REF
ESCK
EOSC
f
133.33
EOSC
EOSC
19.2
1.67
TYP
160
> 2.5V the extended input
(in kHz)
(in kHz)
/8
(in kHz)
LOAD
163.20
O
307.2
2000
MAX
1.70
390
390
136
150
150
150
200
= 20pF.
55
50
pin. The external
D
is the voltage
REF
UNITS
REF
5
kHz
kHz
kHz
kHz
ms
ms
ms
ms
ms
ms
.
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
%
s
s