MCP3304-CI/SL Microchip Technology, MCP3304-CI/SL Datasheet - Page 22

• Manufacturer Part Number: MCP3304-CI/SL
• Description: IC ADC 13BIT 2.7V 4CH SPI 16SOIC
• Manufacturer: Microchip Technology

Specifications of MCP3304-CI/SL

• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Number Of Bits: 13
• Sampling Rate (per Second): 100k
• Data Interface: Serial, SPI™
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Architecture: SAR
• Conversion Rate: 100 KSPs
• Resolution: 12 bit
• Input Type: Voltage
• Snr: 80.02 dB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: MCP3304CI/SL

MCP3302/04
5.5
Inaccurate conversion results may occur if the signal
source for the A/D converter is not a low-impedance
source. Buffering the input will overcome the
impedance issue. It is also recommended that an
analog filter be used to eliminate any signals that may
be aliased back into the conversion results. This is
illustrated in
drive the analog input of the MCP3302/04. This
amplifier provides a low-impedance source for the
converter input and a low-pass filter, which eliminates
unwanted high-frequency noise. Values shown are for
a 10 Hz Butterworth Low-Pass filter.
Low-pass (anti-aliasing) filters can be designed using
Microchip’s interactive FilterLab
will calculate capacitor and resistor values, as well as
determine the number of poles that are required for the
application. For more information on filtering signals,
see Application Note 699 “Anti-Aliasing Analog Filters
for Data Acquisition Systems”.
FIGURE 5-9:
Amplifier is used to implement a 2nd order anti-
aliasing filter for the signal being converted by
the MCP3302/04.
DS21697E-page 22
V
7.86 kΩ
IN
0.1 µF
14.6 kΩ
1 µF
Buffering/Filtering the Analog
Inputs
2.2 µF
Figure
Reference
4.096V
MCP1541
MCP601
5-9, where an op amp is used to
+
-
The MCP601 Operational
C
L
1 µF
®
IN+
IN-
software. FilterLab
V
MCP330X
REF
V
DD
10 µF
0.1 µF
5.6
When laying out a printed circuit board for use with
analog components, care should be taken to reduce
noise wherever possible. A bypass capacitor from V
to ground should always be used with this device and
should be placed as close as possible to the device pin.
A bypass capacitor value of 0.1 µF is recommended.
Digital and analog traces on the board should be
separated as much as possible, with no traces running
underneath the device or the bypass capacitor. Extra
precautions should be taken to keep traces with high-
frequency signals (such as clock lines) as far as
possible from analog traces.
Use of an analog ground plane is recommended in
order to keep the ground potential the same for all
devices on the board. Providing V
devices in a “star” configuration can also reduce noise
by eliminating current return paths and associated
errors (see
layout tips when using the MCP3302/04,MCP3302/04,
or other ADC devices, refer to Application Note 688,
“Layout Tips for 12-Bit A/D Converter Applications”.
FIGURE 5-10:
‘Star’ configuration in order to reduce errors
caused by current return paths.
Device 1
Layout Considerations
Figure
Device 2
5-10). For more information on
V
Connection
© 2008 Microchip Technology Inc.
DD
V
DD
traces arranged in a
Device 3
DD
connections to
Device 4
DD