MT47H128M16RT-25E:C Micron Technology Inc, MT47H128M16RT-25E:C Datasheet - Page 105

• Manufacturer Part Number: MT47H128M16RT-25E:C
• Description: DRAM Chip DDR2 SDRAM 2G-Bit 128Mx16 1.8V 84-Pin FBGA Tray
• Manufacturer: Micron Technology Inc
• Type: DDR2 SDRAMr
• Series: -r

Specifications of MT47H128M16RT-25E:C

• Package: 84FBGA
• Density: 2 Gb
• Address Bus Width: 17 Bit
• Operating Supply Voltage: 1.8 V
• Maximum Clock Rate: 800 MHz
• Maximum Random Access Time: 0.4 ns
• Operating Temperature: 0 to 70 °C
• Format - Memory: RAM
• Memory Type: DDR2 SDRAM
• Memory Size: 2G (128M x 16)
• Speed: 2.5ns
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.9 V
• Package / Case: 84-TFBGA
• Lead Free Status / RoHS Status: Compliant

Table 43: WRITE Using Concurrent Auto Precharge
PDF: 09005aef824f87b6
2gbddr2.pdf – Rev. E 06/10 EN
WRITE with auto precharge
From Command
(Bank n)
the WRITE diagrams show the nominal case, and where the two extreme cases (
[MIN] and
(page 106) shows the nominal case and the extremes of
tion of a burst, assuming no other commands have been initiated, the DQ will remain
High-Z and any additional input data will be ignored.
Data for any WRITE burst may be concatenated with a subsequent WRITE command to
provide continuous flow of input data. The first data element from the new burst is ap-
plied after the last element of a completed burst. The new WRITE command should be
issued x cycles after the first WRITE command, where x equals BL/2.
Figure 59 (page 107) shows concatenated bursts of BL = 4 and how full-speed random
write accesses within a page or pages can be performed. An example of nonconsecutive
WRITEs is shown in Figure 60 (page 107). DDR2 SDRAM supports concurrent auto pre-
charge options, as shown in Table 43.
DDR2 SDRAM does not allow interrupting or truncating any WRITE burst using BL = 4
operation. Once the BL = 4 WRITE command is registered, it must be allowed to com-
plete the entire WRITE burst cycle. However, a WRITE BL = 8 operation (with auto
precharge disabled) might be interrupted and truncated only by another WRITE burst
as long as the interruption occurs on a 4-bit boundary due to the 4n-prefetch architec-
ture of DDR2 SDRAM. WRITE burst BL = 8 operations may not be interrupted or
truncated with any command except another WRITE command, as shown in Figure 61
(page 108).
Data for any WRITE burst may be followed by a subsequent READ command. To follow
a WRITE,
cycles required to meet
WRITE burst may be followed by a subsequent PRECHARGE command.
met, as shown in Figure 63 (page 110).
less of the data mask condition.
WRITE or WRITE with auto precharge
READ or READ with auto precharge
t
PRECHARGE or ACTIVATE
WTR should be met, as shown in Figure 62 (page 109). The number of clock
t
DQSS [MAX]) might not be intuitive, they have also been included. Figure 58
To Command
(Bank m)
t
WTR is either 2 or
105
t
Micron Technology, Inc. reserves the right to change products or specifications without notice.
WR starts at the end of the data burst, regard-
t
WTR/
(with Concurrent Auto Precharge)
2Gb: x4, x8, x16 DDR2 SDRAM
t
CK, whichever is greater. Data for any
(CL - 1) + (BL/2) +
Minimum Delay
t
DQSS for BL = 4. Upon comple-
(BL/2)
1
© 2006 Micron Technology, Inc. All rights reserved.
t
WTR
t
WR must be
WRITE
t
DQSS
Units
t
t
t
CK
CK
CK