SI3206-B-GQ Silicon Laboratories Inc, SI3206-B-GQ Datasheet - Page 118

• Manufacturer Part Number: SI3206-B-GQ
• Description: IC PROSLIC LINE FEED 125V 48TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: ProSLIC®r

Specifications of SI3206-B-GQ

• On-hook Transmission: Yes
• Polarity Reversal: Yes
• On-chip Ring Relay Driver: Yes
• Longitudinal Balanced: 63
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TQFP
• Loop Current Limit: 45mA
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Function: Subscriber Line Interface Concept (SLIC)
• Interface: GCI, PCM, SPI
• Number Of Circuits: 4
• Voltage - Supply: 3.3V
• Current - Supply: *
• Power (watts): *
• Operating Temperature: *
• Mounting Type: Surface Mount
• Package / Case: 48-TQFP Exposed Pad
• Includes: *
• Lead Free Status / RoHS Status: Compliant

Si3232
118
Pin #(s)
24, 37,
25, 38,
19, 62
20, 61
21, 60
22, 59
23, 58
42, 57
41, 56
26, 55
27, 54
29, 30
31, 32
35, 49
36, 48
28
33
34
39
40
43
44
45
BATSELb, BATSELa
THERMb, THERMa
IRINGNb, IRINGNa
IRINGPb, IRINGPa
VRXPb, VRXNb
VTXPb, VTXNb
ITIPNb, ITIPNa
ITIPPb, ITIPPa
VDD2, VDD3,
GND2, GND3
GND4, GND1
GPOb, GPOa
VDD4, VDD1
SRINGACb,
SRINGDCb,
SRINGDCa
SRINGACa
Symbol
RESET
FSYNC
PCLK
SCLK
VCM
SDO
SDI
INT
Output
Input/
O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
Description
RING Transmit Input— Analog input used to sense ac voltage on
RING side of subscriber loop.
RING Sense— Analog current input used to sense dc voltage on
RING side of subscriber loop.
Negative TIP Current Control— Analog current output providing dc
current return path to V
Negative RING Current Control— Analog current output providing
dc current return path to V
Positive TIP Current Control— Analog current output driving dc cur-
rent onto TIP side of subscriber loop in normal polarity. Also modu-
lates ac current onto TIP side of loop.
Supply Voltage— Power supply for internal analog and digital cir-
cuitry. Connect all VDD pins to the same supply and decouple to
adjacent GND pins as close to the pins as possible.
Ground— Ground connection for internal analog and digital circuitry.
Connect all pins to low-impedance ground plane.
Positive RING Current Control— Analog current output driving dc
current onto RING side of subscriber loop in reverse polarity. Also
modulates ac current onto RING side of loop.
Temperature Sensor— Used to sense the internal temperature of
the Si3200. Connect to THERM pin of Si3200 or to V
discrete linefeed circuit.
Common Mode Voltage Input —Connect to external common mode
voltage source.
Differential Analog Receive Input for SLIC Channel b.
Differential Analog Transmit Output for SLIC Channel b.
Reset— Active low. Hardware reset used to place all control registers
in known state. An internal pulldown resistor asserts this pin low
when it is not driven externally.
Frame Sync— 8 kHz frame synchronization signal for internal timing.
May be short or long pulse format.
Battery Voltage Select Pin— Used to switch between high and low
external battery supplies.
General Purpose Driver Output— Used to drive test relays for con-
necting loop test equipment or as a second battery select pin.
PCM System Clock— Master clock input.
Interrupt— Maskable interrupt output. Open drain output for wire-
ORed operation.
Serial Port Bit Clock Input— Controls serial data on SDO and
latches data on SDI.
Serial Port Data Out— Serial port control data output.
Serial Port Data In— Serial port control data input.
Preliminary Rev. 0.96
BAT
BAT
from TIP side of the loop.
from RING side of loop.
DD
when using