MAX1385BETM+ Maxim Integrated Products, MAX1385BETM+ Datasheet - Page 35

• Manufacturer Part Number: MAX1385BETM+
• Description: RF Wireless Misc IC CTRLR LDMOS BIAS 5V
• Manufacturer: Maxim Integrated Products

Specifications of MAX1385BETM+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Set FINECH2 to 1 to load the fine DAC2 output register
with the latest write to DAC2 input registers FINE2 or
FINECAL2. This means that if FINE2 is written to after
FINECAL2, FINE2 is sent to the fine DAC2 output regis-
ter (no calibration code) when FINECH2 is set to 1. Set
HIGHCH2 to 1 to load DAC input register HIWIPE2 into
the Coarse DAC2 High Wiper register. Autocalibration
of the DAC2 high wiper occurs if the HCAL bit in
HIWIPE2 is set to 1. Set LOWCH2 to 1 to load DAC
input register LOWIPE2 into the Coarse DAC2 Low
Wiper register. Autocalibration of the DAC2 low wiper
occurs if the LCAL bit in LOWIPE2 is set to 1.
Set FINECH1 to 1 to load the fine DAC1 output register
with the latest write to DAC input registers FINE1 or
FINECAL1. If FINECAL1 is written to after FINE1,
FINECAL1 is sent to the fine DAC1 output register (with
calibration code) when FINECH1 is set to 1. Set HIGH-
CH1 to 1 to load DAC input register HIWIPE1 into the
Coarse DAC1 output register. Autocalibration of the
DAC1 high wiper occurs if the HCAL bit in HIWIPE1 is
set to 1. Set LOWCH1 to 1 to load DAC input register
LOWIPE1 into the coarse DAC1 output register.
Autocalibration of the DAC1 low wiper occurs if the
LCAL bit in LOWIPE1 is set to 1.
Table 16. ADCCON (Write)
CONCONV
BIT NAME
ADCSEL2
ADCSEL1
Reserved
TEXT2
TEXT1
IEXT2
IEXT1
TINT
X
DATA BIT
D15–D12
D11–D8
D7
D6
D5
D4
D3
D2
D1
D0
______________________________________________________________________________________
POR
X
0
0
0
0
0
0
0
0
0
Don’t care
Reserved; set these bits to 0
1 = Continuous conversions (repeated scans)
0 = Noncontinuous conversions (one scan)
1 = Select voltages at ADCIN2 to be converted
0 = Do not select voltages at ADCIN2 to be converted
1 = Select voltages at PGAOUT2 to be converted
0 = Do not select voltages at PGAOUT2 to be converted
1 = Select temperature at remote diode 2 to be converted
0 = Do not select temperature at remote diode 2 to be converted
1 = Select voltages at ADCIN1 to be converted
0 = Do not select voltages at ADCIN1 to be converted
1 = Select voltages at PGAOUT1 to be converted
0 = Do not select voltages at PGAOUT1 to be converted
1 = Select temperature at remote diode 1 to be converted
0 = Do not select temperature at remote diode 1 to be converted
1 = Select internal temperature of device to be converted
0 = Do not select internal temperature of device to be converted
Dual RF LDMOS Bias Controllers
Write to the Software Clear register to reset the DACs
and FIFO to their POR states (see Table 19). Write to the
Software Clear register by sending the appropriate write
command byte followed by data bits D15–D0. Bits
D15–D10 are don’t care. A write to bits D5–D0 in the
Software Clear register immediately changes the appro-
priate DAC output to its power-on state (regardless of
LDAC). To reset all registers at once, set FULLRESET to
0 and ARMRESET to 1. Next set FULLRESET to 1 and
ARMRESET to 0. This 2-byte reset operation protects the
registers from being fully reset by inadvertent user
writes. After a full reset, the device is in shutdown mode
and the SSHUT register needs to be written to for full
operation.
Set CLFIFO to 1 to clear the entire 15-word FIFO and
FIFO-associated flag bits in the Flag register. Set
HIGHCL2 to 1 to reset the Coarse DAC2 High Wiper
Output and Input registers to their POR states. Set
LOWCL2 to 1 to reset the coarse DAC2 High Wiper
Output and Input registers to their POR states. Set
FINECL1 to 1 to reset Fine DAC1 Output and Input reg-
isters to their POR states. Set HIGHCL1 to 1 to reset
the Coarse DAC1 High Wiper Output and Input regis-
ters to their POR states. Set LOWCL1 to 1 to reset the
with I
FUNCTION
2
C/SPI Interface
SCLR (Write)
35