HFBR-57E5APZ Avago Technologies US Inc., HFBR-57E5APZ Datasheet - Page 6

• Manufacturer Part Number: HFBR-57E5APZ
• Description: MM LC SFP FE DMI ROHS
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-57E5APZ

• Data Rate: 125MBd
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Optical Fiber Type: TX/RX
• Optical Rise Time: 3/2.2ns
• Optical Fall Time: 3/2.2ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1308/1380nm
• Package Type: SFP
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 3. Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each
parameter in isolation, all other parameters having values within the recommended operation conditions. It should not
be assumed that limiting values of more than one parameter can be applied to the products at the same time. Exposure
to the absolute maximum ratings for extended periods can adversely affect device reliability.
Table 4. Recommended Operating Conditions
All the data in this specification refers to the operating conditions above and over lifetime unless otherwise stated.
Notes:
1. The case temperature is measured at the surface of the topside (see figure 5 Module drawing) using a thermocouple connected to the housing.
2. Electrical and optical specifications of the product are guaranteed across recommended case operating temperature range only.
3. Ethernet auto-negotiation pulses are not supported.
Table 5. Transmitter Electrical Characteristics
Notes:
5. Typical value is valid for room temperature and 3.3 V.
6. Connected directly to TX data input pins. AC coupling from pins into driver IC.
Table 6. Receiver Electrical Characteristics
Notes:
7. Differential output voltage is internally AC-coupled but requires an external load termination (100 : differential). The low and high voltages are
8. Data and Data-bar outputs are squelched at LOS assert levels.
6
Parameter
Storage Temperature
Supply Voltage
Data Input Voltage
Parameter
Case Operating Temperature
Supply Voltage
Data Output Load
Signalling Rate (Fast Ethernet)
Parameter
Supply Current
Power Dissipation
Differential Input Voltage
Input Differential Impedance
Transmitter Disable (TX Disable) High
Transmitter Disable (TX Disable) Low
Parameter
Supply Current
Power Dissipation
Data Output: Receiver Differential Output
Voltage (RD+/-)
Data Output Rise Time (10%-90%)
Data Output Fall Time (10%-90%)
Loss of Signal Output Voltage – Low
Loss of Signal Output Voltage – High
measured under this load condition.
Symbol
T
V
V
Symbol
T
V
R
B
Symbol
I
P
V
R
V
V
Symbol
I
P
|V
t
t
LOSV
LOSV
cc
CC
r
f
s
c
cc
i
cc
L
DISS
DISS
DIFF
in
IH
IL
OH
-V
OL
OH
OL
|
Min
-40
3.0
Min
0.5
2.0
0
Min
0.4
2.0
Min
-40
-0.5
-0.5
Typ
3.30
100
125
Typ
60
200
0.8
100
Typ
67
220
Max
+100
3.63
Vcc
Max
+85
3.6
Max
140
500
1.8
3.5
0.8
Max
100
360
2.0
2.20
2.20
0.8
Unit
°C
V
V
Unit
°C
V
:
MBd
Unit
mA
mW
V
:
V
V
Unit
mA
mW
V
ns
ns
V
V
Notes
Notes
Note 1, 2
differential
4B/5B. Note 3
Notes
Note 5
Peak-to-peak
Note 6
Notes
Notes 7, 8