PIC18F452-E/PT Microchip Technology, PIC18F452-E/PT Datasheet - Page 127

• Manufacturer Part Number: PIC18F452-E/PT
• Description: IC MCU CMOS 40MHZ 16K FLSH44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F452-E/PT

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC18
• No. Of I/o's: 34
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Package: 44TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: I2C/SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.0
15.1
The Master Synchronous Serial Port (MSSP) module is
a serial interface useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers, dis-
play drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I
The I
hardware:
• Master mode
• Multi-Master mode
• Slave mode
15.2
The MSSP module has three associated registers.
These include a status register (SSPSTAT) and two
control registers (SSPCON1 and SSPCON2). The use
of these registers and their individual configuration bits
differ significantly, depending on whether the MSSP
module is operated in SPI or I
Additional details are provided under the individual
sections.
© 2006 Microchip Technology Inc.
- Full Master mode
- Slave mode (with general address call)
2
C interface supports the following modes in
MASTER SYNCHRONOUS
SERIAL PORT (MSSP)
MODULE
Master SSP (MSSP) Module
Overview
Control Registers
2
C)
2
C mode.
15.3
The SPI mode allows 8-bits of data to be synchronously
transmitted and received, simultaneously. All four modes
of SPI are supported. To accomplish communication,
typically three pins are used:
• Serial Data Out (SDO) - RC5/SDO
• Serial Data In (SDI) - RC4/SDI/SDA
• Serial Clock (SCK) - RC3/SCK/SCL/LVDIN
Additionally, a fourth pin may be used when in a Slave
mode of operation:
• Slave Select (SS) - RA5/SS/AN4
Figure 15-1 shows the block diagram of the MSSP
module when operating in SPI mode.
FIGURE 15-1:
SCL/LVDIN
RC4/SDI/SDA
RC3/SCK/
RA5/SS/AN4
RC5/SDO
SPI Mode
Read
SS Control
Select
SMP:CKE
Edge
MSSP BLOCK DIAGRAM
(SPI MODE)
Enable
bit0
Select
Edge
PIC18FXX2
TRIS bit
Data to TX/RX in SSPSR
SSPBUF reg
2
SSPM3:SSPM0
SSPSR reg
Clock Select
4
2
DS39564C-page 125
(
Prescaler
4, 16, 64
TMR2 output
Write
clock
shift
Data Bus
Internal
2
T
OSC
)