PIC18F6410-I/PT Microchip Technology, PIC18F6410-I/PT Datasheet - Page 4

• Manufacturer Part Number: PIC18F6410-I/PT
• Description: IC PIC MCU FLASH 8KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6410-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/EUSART/AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
8. Module: A/D
TABLE 2:
9. Module: BOD
TABLE 3:
DS80206F-page 4
D005
A06A
A06
Param
Param
No.
No.
The A/D offset is greater than the specified limit in
Table 26-25 of the Device Data Sheet. The addi-
tional Parameter A06A and updated conditions
and limits are shown in bold text in Table 2.
Work around
Three work arounds exist.
1. Configure the A/D to use the V
The BOD module may reset below the minimum
operating voltage of the device when configured
for BORV1:BORV0 = 11. The updated Reset
voltage specifications are shown in bold in
Table 3.
Work around
Use the next higher BOD voltage setting to ensure
a low V
Date Codes that pertain to this issue:
All engineering and production devices.
V
pins for the voltage references. This is done by
setting the VCFG<1:0> bits (ADCON1<5:4>).
Sym
Symbol
E
E
BOR
OFF
OFF
DD
Brown-out Reset Voltage
PIC18LF6310/6410/8310/8410
BORV1:BORV0 = 11 N/A 2.05 N/A
A/D CONVERTER CHARACTERISTICS: PIC18F6310/6410/8310/8410 (INDUSTRIAL)
is detected above 2.0V.
BROWN-OUT RESET VOLTAGE
Characteristic
Offset Error
Offset Error
Characteristic
Min Typ Max Unit
REF
+ and V
REF
V
Min
—
—
-
PIC18LF6310/6410/8310/8410 (INDUSTRIAL)
10. Module: EUSART
Typ
—
—
2. Perform a conversion on a known voltage
3. Increase system clock speed to 40 MHz and
Date Codes that pertain to this issue:
All engineering and production devices.
When performing back-to-back transmission in
9-bit mode (TX9D bit in the TXSTAx register is
set), an ongoing transmission’s timing can be
corrupted if the TX9D bit (for the next trans-
mission) is not written immediately following the
setting of TXxIF. This is because any write to
the TXSTAx register results in a reset of the
Baud Rate Generator which will effect any
ongoing transmission.
Work around
Load TX9D just after TXxIF is set, either by polling
TXxIF or by writing TX9D at the beginning of the
Interrupt Service Routine, or only write to TX9D
when
(TRMT = 1).
Date Codes that pertain to this issue:
All engineering and production devices.
reference voltage and adjust the A/D result in
software.
adjust A/D settings accordingly. Higher system
clock frequencies decrease offset error.
<±1.5
<±3.5
Max
a
transmission
Units
LSb
LSb
© 2007 Microchip Technology Inc.
V
V
REF
REF
is
= V
= V
Conditions
not
REF
SS
and V
in
+ and V
progress
DD
REF
-