PIC18F45J50-I/PT Microchip Technology, PIC18F45J50-I/PT Datasheet - Page 34

• Manufacturer Part Number: PIC18F45J50-I/PT
• Description: IC PIC MCU FLASH 32K 2V 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45J50-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Timers: 5
• Operating Supply Voltage: 2.25 V to 2.75 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, MA180024, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Controller Family/series: PIC18
• No. Of I/o's: 22
• Ram Memory Size: 3776Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Embedded Interface Type: EUSART, I2C, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F46J50 FAMILY
REGISTER 2-1:
2.3
When the PIC18F46J50 Family devices are used for
USB connectivity, a 6 MHz or 48 MHz clock must be
provided to the USB module for operation in either
Low-Speed or Full-Speed modes, respectively. This
may require some forethought in selecting an oscillator
frequency and programming the device.
The full range of possible oscillator configurations
compatible with USB operation is shown in Table 2-5.
2.3.1
The USB clock for Low-Speed mode is derived from the
primary oscillator or from the 96 MHz PLL. In order to
operate the USB module in Low-Speed mode, a 6 MHz
clock must be provided to the USB module. Due to the
way the clock dividers have been implemented in the
DS39931C-page 34
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5-0
INTSRC
R/W-0
Oscillator Settings for USB
LOW-SPEED OPERATION
INTSRC: Internal Oscillator Low-Frequency Source Select bit
1 = 31.25 kHz device clock derived from 8 MHz INTOSC source (divide-by-256 enabled)
0 = 31 kHz device clock derived directly from INTRC internal oscillator
PLLEN: Frequency Multiplier Enable bit
1 = 96 MHz PLL is enabled
0 = 96 MHz PLL is disabled
TUN<5:0>: Frequency Tuning bits
011111 = Maximum frequency
011110
•
•
•
000001
000000 = Center frequency; oscillator module is running at the calibrated frequency
111111
•
•
•
100000 = Minimum frequency
PLLEN
R/W-0
OSCTUNE: OSCILLATOR TUNING REGISTER (ACCESS F9Bh)
W = Writable bit
‘1’ = Bit is set
R/W-0
TUN5
R/W-0
TUN4
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
TUN3
PIC18F46J50 Family, the microcontroller core must
run at 24 MHz in order for the USB module to get the
6 MHz clock needed for low-speed USB operation.
Several clocking schemes could be used to meet these
two required conditions. See Table 2-4 and Table 2-5
for possible combinations which can be used for
low-speed USB operation.
TABLE 2-4:
Clock
Input
48
24
Clock
CPU
24
24
R/W-0
TUN2
CLOCK FOR LOW-SPEED USB
CPDIV<1:0>
© 2009 Microchip Technology Inc.
x = Bit is unknown
‘10’
‘11’
R/W-0
TUN1
48/8 = 6 MHz
24/4 = 6 MHz
USB Clock
R/W-0
TUN0
bit 0