63819-0100 Molex Inc, 63819-0100 Datasheet - Page 4

• Manufacturer Part Number: 63819-0100
• Description: TOOL HAND CRIMP 24-30AWG
• Manufacturer: Molex Inc
• Series: PremiumGrade™, MicroBlade™, Milli-Grid™r

Specifications of 63819-0100

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• Crimp Size: 30AWG To 24AWG
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 24-30 AWG
• For Use With: WM18965TR - CONN SOCKET 24-30AWG CRIMP TINWM18965CT - CONN SOCKET 24-30AWG CRIMP TINWM2139 - CONN TERM FEMALE 24-30AWG 30GOLDWM2139TR - CONN TERM FEMALE 24-30AWG 30GOLDWM1128CT - CONN TERM FEMALE 24-30AWG GOLDWM1128TR - CONN TERM FEMALE 24-30AWG GOLDWM18992 - CONN SOCKET 24-30AWG CRIMP TINWM1128 - CONN TERM FEMALE 24-30AWG CRIMP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 063819-0100; 063819-0100-P; 0638190100; 0638190100-P; 63819-0100-P; 638190100; 638190100-P; WM9020

Hand Crimp Tool for Milli-Grid™ and MicroBlade Crimp Terminal
Doc No: ATS-638190100
Revision: A
8. Remove the crimped terminal from the terminal
9. Visually inspect the crimped terminal for proper
10. On some large O.D. wires, it may not be possible
Note:
A crimp height chart is provided with this manual
as Reference Only. Due to the wide range of
wires, strands, insulation diameters, and
durometers available, actual crimp height
measurements may very slightly. An occasional,
destructive, pull force test should be performed
to check hand tool crimp. Pull Force value Must
exceed the Minimum pull force specifications
listed.
Locator Replacement
See the parts list on the last page of this
document for the proper locator order number.
Follow the steps below to replace the locator.
1. Open the crimp hand tool.
2. Squeeze gently on the lower area shown in
3. Lift and pull away from the hand tool. The top
4. To reinstall the new locator, make sure the hand
5. Press the red insert down as far as it will go as
6. Holding onto the lower part of the locator with your
7. Rotate the locator down and press the lower tabs
locator by pulling on the wire.
crimp location.
to insert the wire with the tool partially closed.
Those wires should be inserted with the hand tool
in the open position. Insert the wire above the
terminal in the punch and against the wire stop
then close the tool. See Figure 6.
Figure 7A with your thumb and index finger.
The lower tabs of the locator should
disengage from the hand tool.
locator hooks should slip out of the top slots easily.
See Figure 7A.
tool is in the open position.
shown in Figure 7B.
thumb and index finger, insert the locators top
hooks (2) into the hand tool top slots.
into the two bottom slots of the hand tool. To
secure the locator into place, the lower tabs must
snap into place on the hand tool frame.
Release Date: 11-26-07
Revision Date: 11-26-07
SQUEEZE
HERE
UNCONTROLLED COPY
Figure 7A
M3 BHCS
TOOLING
LOWER TABS
Figure 8
LOCATOR
TOP SLOTS OF
PULL OPEN
HANDTOOL
TERMINAL
TOP HOOKS
WIRE STOP
Figure 6
WIRE
JAWS OPEN
PUSH ON
HANDLE
SQUEEZE
HERE
CENTER OF LOCATOR
DOWN POSITION
MAKE SURE
IS IN THE
Figure 7B
Page 4 of 8
TOOLING