LD2T06P0 Red Lion Controls, LD2T06P0 Datasheet - Page 11

• Manufacturer Part Number: LD2T06P0
• Description: TIMER 6 DIGIT 2.25" 120VAC RED
• Manufacturer: Red Lion Controls
• Series: LDr
• Type: Timerr

Specifications of LD2T06P0

• No. Of Digits / Alpha: 6
• Digit Height: 57mm
• Power Consumption: 26VA
• Operating Temperature Range: 0°C To +50°C
• Signal Input Type: Pulse
• Character Size: 2.25"
• Ip/nema Rating: IP65 / NEMA 4X
• Accuracy: ±0.01% %
• Connection Type: Wire Leads
• Dimensions: 16"L×2.25"W×4"H
• Display Digit Height: 2.25 "
• Display Resolution: 0.001 Sec. (Minimum Digit), 1 hr. (Single Digit)
• Display Type: LED
• Function: Timer
• Material, Casing: Aluminum
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: 0 to 999999
• Special Features: RS485/RS232 Communications
• Termination: Terminal Block
• Voltage, Supply: 85 to 250/11 to 16 VAC/VDC
• Counter Supply Voltage: 85-250VAC/11-16VDC
• Display Font Color: Red
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC119


Normally, the baud rate is set to the highest value that all of the serial
communications equipment is capable of transmitting and receiving.

other serial communications equipment on the serial link.

data word length. Set the parity bit to match that of the other serial equipment
on the serial link. The meter ignores parity when receiving data and sets the
parity bit for outgoing data. If parity is set to
to force the frame size to 10 bits.

and a value of zero can be used (RS232 applications). Otherwise, with multiple
bussed units, a unique address number must be assigned to each meter. The
node address applies specifically to RS485 applications.
5.5 MODULE 5 - S


Parameters. These parameters are used to match the serial settings of the meter
with those of the host computer or other serial device.


Set the baud rate to match that of other serial communications equipment.
Select either 7- or 8-bit data word length. Set the word length to match the
This parameter only appears when the Data Bit parameter is set to a 7-bit
Enter the serial node address. With a single unit, an address is not needed
Module 5 is the programming module for the Serial Communications

PAR

Baud Rate






METER ADDRESS




BAUD RATE
PARITY BIT
DATA BIT
to

Data Bit



 

, an additional stop bit is used



ERIAL
Parity Bit


PARAMETER MENU
C
OMMUNICATIONS
11
Address
Meter

in response to a Transmit Value command or a Block Print Request. Select
for a full print transmission, consisting of the meter address, mnemonics, and
parameter data. Select
parameter data only. This setting is applied to all the parameters selected in the
PRINT OPTIONS. (Note: If the meter address is 0, the address will not be sent
during a full transmission.)

Request. A print request is also referred to as a block print because more than
one parameter can be sent to a printer or computer as a block.
in the print block. All active parameters entered as
transmitted during a block print. Parameters entered as
(
setting. For example, the Cycle Counter and Cycle Counter Start values will
only be sent when the Cycle Counter is enabled. If disabled, these parameters
are inactive and will not be transmitted. Likewise, only the Setpoint parameters
that apply to the programmed Setpoint Output Action will be transmitted.



This parameter determines the formatting of data transmitted from the meter
This parameter selects the meter values transmitted in response to a Print
Selecting
The “Print All” (
Note: Inactive parameters will not be sent regardless of the print option
DISPLAY








), without having to individually select each parameter in the sublist.

Abbreviated


displays a sublist for choosing the meter parameters to appear


Setpoint Time-out
Printing

Cycle Counter
Counter Start
Setpoint OFF
DESCRIPTION
Setpoint ON
ABBREVIATED PRINTING

Timer Start
Timer Stop
P
Timer
for abbreviated print transmissions, consisting of the
ARAMETERS
PRINT OPTIONS
) option selects all meter values for transmitting


FACTORY
SETTING
Options
Print











MNEMONIC

(
in the sublist will be
TMR
CNT
SOF
STO
TST
TSP
CST
SPT

will not be sent.
)
