DG-ACC-JBST Digi International, DG-ACC-JBST Datasheet - Page 115
DG-ACC-JBST
Manufacturer Part Number
DG-ACC-JBST
Description
JTAG-BOOSTER FOR NETSILICON 3.3V
Manufacturer
Digi International
Series
Digi/FS Forthr
Type
FLASHr
Datasheet
1.DG-ACC-JBST.pdf
(126 pages)
Specifications of DG-ACC-JBST
Contents
Programmer and Associated Interface Software
For Use With/related Products
NetSilicon NS9360, NS9750, NS9775
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
FS-9051
FS-9051
FS-9051
- Current page: 115 of 126
- Download datasheet (4Mb)
Use: JTAG270 /P filename [optionlist]
Options
Program a Flash Device
The specified file is programmed into the flash memory. The flash status is polled
after each cell is programmed (cell = 8-, 16- or 32-bit, depending on current data bus
width). In the case of a programming error, the contents of the flash memory are
written to a file with the extension DMP.
For a complete verify after programming, use an additional command line with the
verify function. In most cases, this additional verify step is not needed.
Software normally detects the type of the flash device. When auto-detection fails,
you should use the
right flash device and configuration.
/DEVICE=devicename
The flash device is detected automatically by switching to auto-select mode. In case
of trouble, select the flash device using this parameter to avoid auto-detection.
Combine this option with one of the following options that specify the data bus width
and the option
/8BIT /16BIT /32BIT
Specifies the data bus width to the target flash device. You can speed up
auto-detection if you specify the correct data bus size. You need this option together
with the
/BYTE-MODE
If there is a flash device connected to the CPU, which has a byte mode pin (8 bit and
16/32 bit bus mode), you can force it to be used as 8 bit mode with the option
/BYTE-MODE
/CFI
To be prepared for future flash chips, the JTAG-Booster integrates support for flashes
that contain the CFI (Common Flash Interface) information structure. CFI support is
/DEVICE=
. In most cases, this option will not be needed.
/BYTE-MODE
option to explicitly specify a particular flash configuration.
/DEVICE=
, if applicable.
option together with /8BIT or /16BIT or /32BIT to set the
w w w . d i g i . c o m
J T A G - B o o s t e r f o r I n t e l X S c a l e P X A 2 7 0
1 0 3
Related parts for DG-ACC-JBST
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT POE APPLICATION
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT EV SATELLITE MODEM DIGI M10
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE SATELLITE MODEM DIGI M10
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
SWITCH LEVER 50MA INSERT LEFT
Manufacturer:
Cherry Electrical
Datasheet:
Part Number:
Description:
KIT JUMP START ME 9210 NET+OS 7
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT JUMP START ME 9210 LINUX
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT INTEGRATION ME MOD S MODELS
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADPT NO RAVEN
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
KIT DEV SP ADAPTER
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
IC ARM MICROPROCESSOR 177BGA
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
DIGI CONNECT 4MB FLASH 8MB RAM
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 9P 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International/Maxstream
Datasheet: