DS21448LDK Maxim Integrated Products, DS21448LDK Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS21448LDK
Manufacturer Part Number
DS21448LDK
Description
KIT DESIGN LIU DS21448L T1/J1/E1
Manufacturer
Maxim Integrated Products
Datasheet
1.DS21448L.pdf
(60 pages)
Specifications of DS21448LDK
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Note 1: G.703 requires an accuracy of ±50ppm for T1 and E1. TR62411 and ANSI specs require ±32ppm accuracy for T1 interfaces.
3. DETAILED DESCRIPTION
The DS21448 has a usable receiver sensitivity of 0 to -43dB for E1 applications and 0 to -36dB for T1 that allows it
to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6000ft (T1) in length. The user has the option to use
internal receive termination, software selectable for 75Ω, 100Ω, and 120Ω applications, or external termination.
The on-board crystal-less jitter attenuator can be placed in either the transmit or the receive data path, and requires
only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1
applications).
The DS21448 has diagnostic capabilities such as loopbacks and PRBS pattern generation and detection. 16-bit
loop-up and loop-down codes can be generated and detected. A single input pin can power down all transmitters to
allow the implementation of hitless protection switching (HPS) for 1+1 redundancy without the use of relays. The
device can be controlled through an 8-bit parallel port (muxed or nonmuxed) or a serial port, and it can be used in
hardware mode. A standard boundary scan interface supports board-level testing.
The DS21448 contains four independent LIUs that share a common interface for configuration and status. The user
can choose between three different means of accessing the device: a parallel microprocessor interface, a serial
interface, and a hardwired mode, which configures the device by setting levels on the device’s pins. The
DS21448’s four chip selects (CS1, CS2, CS3, and CS4) determine which LIU is accessed when using the parallel
or serial interface modes. Four sets of identical register maps exist, one for each channel. Using the appropriate
chip select accesses a channel’s register map.
The analog AMI/HDB3 waveform off the E1 line or the AMI/B8ZS waveform off the T1 line is transformer-coupled
into the RTIP and RRING pins of the DS21448. The user has the option to use internal termination, software
selectable for 75Ω/100Ω/120Ω applications, or external termination. The device recovers clock and data from the
analog signal and passes it through the jitter attenuation mux, outputting the received line clock at RCLK and
bipolar or NRZ data at RPOS and RNEG. The DS21448 contains an active filter that reconstructs the analog-
received signal for the nonlinear losses that occur in transmission. The receive circuitry is also configurable for
various monitor applications. The device has a usable receive sensitivity of 0 to -43dB for E1 and 0 to -36dB for T1
that allows the device to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in length. Data
input at TPOS and TNEG is sent through the jitter attenuation mux to the waveshaping circuitry and line driver. The
DS21448 drives the E1 or T1 line from the TTIP and TRING pins through a coupling transformer. The line driver
can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for T1.
3.1 DS21448 and DS21Q348 Differences
The DS21448 BGA is a monolithic quad-port LIU that is a replacement for the DS21Q348. The additional features
of JTAG, transmit driver disable, and the serial interface in the DS21448 have changed the function of several pins,
as shown in
Table 3-A. DS21448 vs. DS21Q348 Pin Differences
*
DS21448 pin is internally pulled up.
TVSS1–TVSS4
VSS1–VSS4
PIN
G4
M3
M5
M6
M7
K1
K3
K7
L3
J1
PIN
Table
3-A.
I/O
—
—
DS21Q348
TEST
VSM
VSS
VSS
N.C.
N.C.
N.C.
N.C.
N.C.
A4
Transmitter Signal Ground for Transmitter Outputs
Signal Ground
TXDIS/TEST
DS21448
A4/SDO
JTRST*
JTCLK
JTMS*
SCLK
JTDO
JTDI*
N.C.
SDI
13 of 60
FUNCTION