DS21448LDK Maxim Integrated Products, DS21448LDK Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS21448LDK
Manufacturer Part Number
DS21448LDK
Description
KIT DESIGN LIU DS21448L T1/J1/E1
Manufacturer
Maxim Integrated Products
Datasheet
1.DS21448L.pdf
(60 pages)
Specifications of DS21448LDK
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Table 2-D. Serial Interface Mode Pin Description
RRING1–RRING4
PBEO1–PBEO4
TPOS1–TPOS4
TNEG1–TNEG4
TVDD1–TVDD4
RCLK1–RCLK4
TVSS1–TVSS4
TCLK1–TCLK4
RCL1/LOTC1–
RTIP1–RTIP4
RCL4/LOTC4
VDD1–VDD4
TXDIS/TEST
VSS1–VSS4
BIS0/BIS1
JTRST
JTCLK
OCES
MCLK
HRST
SCLK
JTMS
JTDO
ICES
SDO
JTDI
VSM
CS1
CS2
CS3
CS4
PIN
SDI
INT
PIN
I/O
I/O
I/O
—
—
—
—
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Interrupt (INT). Flags host controller during conditions and change of conditions defined in the
status register. Active-low, open-drain output.
Tri-State Control, Multifunctional. Set this pin high with all CS1–CS4 inputs inactive to tri-state
TTIP1–TTIP4 and TRING1–TRING4. Set this pin high with any of the CS1–CS4 inputs active to
tri-state all outputs and I/O pins (including the parallel control port). Set low for normal operation.
Hardware Reset. Bringing HRST low resets the DS21448, setting all control bits to the all-zeros
default state.
Master Clock. A 2.048MHz (±50ppm) clock source with TTL levels is applied at this pin. This
clock is used internally for both clock/data recovery and for jitter attenuation. A T1 1.544MHz
clock source is optional (Note 1).
Bus Interface Select Bit 0 and 1. Used to select bus interface option. See
Chip Select 1. Must be low to read or write to channel 1 of the device. CS1 is an active-low
signal.
Chip Select 2. Must be low to read or write to channel 2 of the device. CS2 is an active-low
signal.
Chip Select 3. Must be low to read or write to channel 3 of the device. CS3 is an active-low
signal.
Chip Select 4. Must be low to read or write to channel 4 of the device. CS4 is an active-low
signal.
Input Clock-Edge Select. Selects whether the serial interface data input (SDI) is sampled on the
rising (ICES = 0) or falling edge (ICES = 1) of SCLK.
Output Clock-Edge Select. Selects whether the serial interface data output (SDO) changes on
the rising (OCES = 1) or falling edge (OCES = 0) of SCLK.
Serial Clock. Serial interface clock.
Serial Data Input. Serial interface data input.
Serial Data Output. Serial interface data output.
PRBS Bit-Error Output. The receiver constantly searches for a 2
PRBS, depending on the ETS bit setting (CCR1.7). It remains high if it is out of synchronization
with the PRBS pattern. It goes low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization cause a positive-going pulse (with same period as E1 or
T1 clock) synchronous with RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to logic 1.
Receive Carrier Loss/Loss-of-Transmit Clock. An output that toggles high during a receive carrier
loss (CCR2.7 = 0) or toggles high if the TCLK pin has not been toggled for 5µs ± 2µs
(CCR2.7 = 1). CCR2.7 defaults to logic 0 when in hardware mode.
Receive Tip and Ring. Analog inputs for clock recovery circuitry. These pins connect through a
1:1 transformer to the line. See Section
Receive Clock. Buffered recovered clock from the line. Synchronous to MCLK in absence of
signal at RTIP and RRING.
Transmit Positive Data. Sampled on the falling edge (CCR2.1 = 0) or the rising edge
(CCR2.1 = 1) of TCLK for data to be transmitted out onto the line.
Transmit Negative Data. Sampled on the falling edge (CCR2.1 = 0) or the rising edge
(CCR2.1 = 1) of TCLK for data to be transmitted out onto the line.
Transmit Clock. A 2.048MHz or 1.544MHz primary clock. It is used to clock data through the
transmit-side formatter. It can be sourced internally by MCLK or RCLK. See Common Control
Register 1 and
JTAG Reset
JTAG Mode Select
JTAG Clock
JTAG Data In
JTAG Data Out
Voltage Supply Mode (LQFP only). Should be wired low for correct operation.
3.3V, ±5% Transmitter Positive Supply
3.3V, ±5% Positive Supply
Transmitter Signal Ground
Signal Ground
Figure
1-3.
10 of 60
7
for details.
FUNCTION
FUNCTION
15
- 1 (E1) or a QRSS (T1)
Table 2-A
for details.