COP8SA-DM National Semiconductor, COP8SA-DM Datasheet - Page 231
COP8SA-DM
Manufacturer Part Number
COP8SA-DM
Description
MODULE DEBUGGING FOR COP8SA
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of COP8SA-DM
Module/board Type
Debugger Module
For Use With/related Products
Cop 8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*COP8SA-DM
- Current page: 231 of 254
- Download datasheet (2Mb)
4.14.1 Typical Application Requirements
Keyboard Scanning
The keyboard is organized as an 8 input by 16 output matrix. Software key rollover
eliminates the need for decoupling diodes in the 16 by 8 key matrix. The COP8SAC7’s L
port is configured as a weak pull-up input port, thus allowing the use of the Multi-Input
Wakeup feature. Most of the time the chip is in the current saving HALT mode (<4 A)
Any keystroke or a data transmission from the computer will create a high-to-low
transition one of the L lines, which wakes up the microcontroller from HALT mode. After
returning from the HALT mode, the keyboard is scanned in order to detect which key is
pressed and the appropriate key code is sent to the computer. This event-driven key-
board scanning technique results in lowest possible current consumption because the
HALT mode is used between successive keystrokes.
LED Direct Drive
Three LEDs are driven directly by three of the device high sink D-lines (15 mA sink
capability), thus eliminating the need for additional LED drivers or transistors.
• Single Chip solution
• Low cost on-chip R/C oscillator (or optional ceramic oscillator)
• Output pins have LED direct drive capability
• Internal power-on reset
• Programmable I/O with on-chip pull-ups
• Powerful table lookup and indirect addressing modes
• Fully static HALT mode with hardware restart capability
• Multi-Input Wakeup
• WATCHDOG timer
• 254 consecutive bytes of table lookup data in one block
• Multi-source interrupt (external interrupt with selectable edge, timer interrupt
• Schmitt trigger inputs
with selectable edge, and software interrupt)
COP8SAx7 APPLICATION IDEAS
4-39
Related parts for COP8SA-DM
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROGRAMING UNIT FOR COP8SA PARTS
Manufacturer:
National Semiconductor
Part Number:
Description:
ADAPTER SOIC 16,20,28,44 PLCC
Manufacturer:
National Semiconductor
Part Number:
Description:
8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory/ Power On Reset/ and Very Small Packaging
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet: