AD9518-3/PCBZ Analog Devices Inc, AD9518-3/PCBZ Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9518-3/PCBZ
Manufacturer Part Number
AD9518-3/PCBZ
Description
BOARD EVAL FOR AD9518-3
Manufacturer
Analog Devices Inc
Specifications of AD9518-3/PCBZ
Main Purpose
Timing, Clock Generator
Utilized Ic / Part
AD9518-3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
VCO calibration must be manually initiated. This allows for
flexibility in deciding what order to program registers and when
to initiate a calibration, instead of having it happen every time
certain PLL registers have their values changed. For example,
this allows for the VCO frequency to be changed by small
amounts without having an automatic calibration occur each
time; this should be done with caution and only when the user
knows the VCO control voltage is not going to exceed the nominal
best performance limits. For example, a few 100 kHz steps are
fine, but a few MHz might not be. Additionally, because the
calibration procedure results in rapid changes in the VCO
frequency, the distribution section is automatically placed in
SYNC until the calibration is finished. Therefore, this
temporary loss of outputs must be expected.
A VCO calibration should be initiated under the following
conditions:
• After changing any of the PLL R, P, B, and A divider settings,
• Whenever system calibration is desired. The VCO is designed
CLOCK DISTRIBUTION
A clock channel consists of a pair of outputs that share a
common divider. The AD9518 has three channels, each with
two LVPECL outputs, for a total of six LVPECL outputs.
Each channel has its own programmable divider that divides the
clock frequency applied to its input by any integer from 1 to 32.
Because the internal VCO frequency is above the maximum
channel divider input frequency (1600 MHz), the VCO divider
must be used after the on-chip VCO. The VCO divider can be
set to divide by 2, 3, 4, 5, or 6. External clock signals connected
to the CLK input also require the VCO divider if the frequency
of the signal is greater than 1600 MHz.
The channel dividers allow for a selection of various duty cycles,
depending on the currently set division; that is, for any specific
division, D, the output of the divider can be set to high for
N + 1 input clock cycles and low for M + 1 input clock cycles
(where D = N + M + 2). For example, a divide-by-5 can be high
for one divider input cycle and low for four cycles, or a divide-
by-5 can be high for three divider input cycles and low for two
cycles. Other combinations are also possible.
The channel dividers include a duty-cycle correction function
that can be disabled. In contrast to the selectable duty cycle
just described, this function can correct a non-50% duty cycle
caused by an odd division. However, this requires that the
division be set by M = N + 1.
or after a change in the PLL reference clock frequency. This,
in effect, means any time a PLL register or reference clock is
changed such that a different VCO frequency results.
to operate properly over extremes of temperatures even when
it is first calibrated at the opposite extreme. However, a VCO
calibration can be initiated at any time, if desired.
Rev. 0 | Page 35 of 64
In addition, the channel dividers allow a coarse phase offset or
delay to be set. Depending on the division selected, the output
can be delayed by up to 31 input clock cycles. The divider
outputs can also be set to start high or to start low.
Internal VCO or External CLK as Clock Source
The clock distribution of the AD9518 has two clock input
sources: an internal VCO or an external clock connected to the
CLK/ CLK pins. Either the internal VCO or CLK must be
chosen as the source of the clock signal to distribute. When the
internal VCO is selected as the source, the VCO divider must be
used. When CLK is selected as the source, it is not necessary to
use the VCO divider if the CLK frequency is less than the
maximum channel divider input frequency (1600 MHz);
otherwise, the VCO divider must be used to reduce the
frequency to one acceptable by the channel dividers. Table 29
shows how the VCO, CLK, and VCO divider are selected.
0x1E1<1:0> selects the channel divider source and determines
whether the VCO divider is used. It is not possible to select the
VCO without using the VCO divider.
Table 29. Selecting VCO or CLK as Source for Channel
Divider, and Whether VCO Divider Is Used
<1>
0
0
1
1
CLK or VCO Direct to LVPECL Outputs
It is possible to connect either the internal VCO or the CLK
(whichever is selected as the input to the VCO divider) directly
to the LVPECL outputs, OUT0 to OUT5. This configuration
can pass frequencies up to the maximum frequency of the VCO
directly to the LVPECL outputs. The LVPECL outputs may not
be able to provide a full voltage swing at the highest frequencies.
To connect the LVPECL outputs directly to the internal VCO or
CLK, the VCO divider must be selected as the source to the
distribution section, even if no channel uses it.
Either the internal VCO or the CLK can be selected as the
source for the direct to output routing.
Table 30. Settings for Routing VCO Divider Input Directly
to LVPECL Outputs
Register Setting
0x1E1<1:0> = 00b
0x1E1<1:0> = 10b
0x192<1> = 1b
0x195<1> = 1b
0x198<1> = 1b
0x1E1
<0>
0
1
0
1
Channel Divider Source
CLK
CLK
VCO
Not allowed
Selection
CLK is the source; VCO divider selected
VCO is the source; VCO divider selected
Direct to output OUT0, OUT1
Direct to output OUT2, OUT3
Direct to output OUT4, OUT5
AD9518-3
VCO Divider
Used
Not used
Used
Not allowed