AD9518-3/PCBZ Analog Devices Inc, AD9518-3/PCBZ Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9518-3/PCBZ
Manufacturer Part Number
AD9518-3/PCBZ
Description
BOARD EVAL FOR AD9518-3
Manufacturer
Analog Devices Inc
Specifications of AD9518-3/PCBZ
Main Purpose
Timing, Clock Generator
Utilized Ic / Part
AD9518-3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Reference Switchover
The AD9518 supports dual single-ended CMOS inputs, as well
as a single differential reference input. In the dual single-ended
reference mode, the AD9518 supports automatic and manual
PLL reference clock switching between REF1 (on Pin REFIN)
and REF2 (on Pin REFIN ). This feature supports networking
and other applications that require redundant references. When
using reference switchover, the single-ended reference inputs
should be dc-coupled CMOS levels and should never be allowed
to go to high impedance. If these inputs are allowed to go to high
impedance, noise may cause the buffer to chatter, causing a
false detection of the presence of a reference.
There are several configurable modes of reference switchover.
The switchover can be performed manually or automatically.
The manual switchover is done either through a register setting
(0x1C) or by using the REF_SEL pin. The automatic switchover
occurs when REF1 disappears. There is also a switchover deglitch
feature, which ensures that the PLL does not receive rising edges
that are far out of alignment with the newly selected reference.
There are two reference automatic switchover modes (0x1C):
• Prefer REF1: Switch from REF1 to REF2 when REF1
• Stay on REF2: Automatically switch to REF2 if REF1 disappears,
REFIN
REFIN
disappears. Return to REF1 from REF2 when REF1 returns.
but do not switch back to REF1 if it reappears. The reference
can be set back to REF1 manually at an appropriate time.
REF1
REF2
Figure 32. REFIN Equivalent Circuit
10kΩ
10kΩ
85kΩ
85kΩ
12kΩ
10kΩ
V
V
150Ω
150Ω
S
S
V
S
Rev. 0 | Page 29 of 64
In automatic mode, REF1 is monitored by REF2. If REF1
disappears (two consecutive falling edges of REF2 without an
edge transition on REF1), REF1 is considered missing. Upon
the next subsequent rising edge of REF2, REF2 is used as the
reference clock to the PLL. If 0x1C<3> = 0b (default), when
REF1 returns (four rising edges of REF1 without two falling
edges of REF2 between the REF1 edges), the PLL reference
switches back to REF1. If 0x1C<3> = 1b, the user can control
when to switch back to REF1. This is done by programming the
part to manual reference select mode (0x1C<4> = 0b) and by
ensuring that the registers and/or REF_SEL pin are set to select
the desired reference. Automatic mode can be re-enabled when
REF1 is reselected.
Manual switchover requires the presence of a clock on the
reference input that is being switched to, or that the deglitching
feature be disabled (0x1C<7>).
Reference Divider R
The reference inputs are routed to the reference divider, R.
R (a 14-bit counter) can be set to any value from 0 to 16,383 by
writing to 0x11 and 0x12. (Both R = 0 and R = 1 give divide-by-1.)
The output of the R divider goes to one of the PFD inputs to be
compared with the VCO frequency divided by the N divider.
The frequency applied to the PFD must not exceed the maximum
allowable frequency, which depends on the antibacklash pulse
setting (see Table 2).
The R counter has its own reset. The R counter can be reset
using the shared reset bit of the R, A, and B counters. It can also
be reset by a SYNC operation.
VCXO/VCO Feedback Divider N: P, A, B, R
The N divider is a combination of a prescaler (P) and two counters,
A and B. The total divider value is
where P can be 2, 4, 8, 16, or 32.
Prescaler
The prescaler of the AD9518 allows for two modes of operation:
a fixed divide (FD) mode of 1, 2, or 3 and dual modulus (DM)
mode where the prescaler divides by P and (P + 1) {2 and 3, 4
and 5, 8 and 9, 16 and 17, or 32 and 33}. The prescaler modes of
operation are given in Table 43, 0x16<2:0>. Not all modes are
available at all frequencies (see Table 2).
When operating the AD9518 in dual modulus mode (P//P + 1),
the equation used to relate input reference frequency to VCO
output frequency is
However, when operating the prescaler in FD mode 1, 2, or 3,
the A counter is not used (A = 0) and the equation simplifies to
When A = 0, the divide is a fixed divide of P = 2, 4, 8, 16, or 32,
in which case the previous equation also applies.
N = (P × B) + A
f
f
VCO
VCO
= (f
= (f
REF
REF
/R) × (P × B + A) = f
/R) × (P × B) = f
REF
× N/R
REF
× N/R
AD9518-3