ST7MDTULS-EVAL STMicroelectronics, ST7MDTULS-EVAL Datasheet
ST7MDTULS-EVAL
Specifications of ST7MDTULS-EVAL
Available stocks
Related parts for ST7MDTULS-EVAL
ST7MDTULS-EVAL Summary of contents
Page 1
... STMicroelectronics ST7MDTULS-EVAL ST7 USB low-speed evaluation board UM0068 User manual Rev 2 October 2007 ...
Page 2
BLANK ...
Page 3
... Introduction The objective of the ST7MDTULS-EVAL evaluation board is to provide a complete USB application package using a Windows-based host software application and one of ST’s range of USB low-speed microcontrollers acting as a peripheral device. The host software and the ST7 source code provide an easily-understood example of how to exchange data using the HID (human interface devices) class protocols ...
Page 4
Contents Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
UM0068 List of tables Table 1. Description of evaluation board probing points ...
Page 6
List of figures List of figures Figure 1. Evaluation board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 7
... Getting started 1.1 System requirements In order to use the ST7MDTULS-EVAL with the Windows operating system, a recent version of Windows, such as Windows 98, Windows Millennium, Windows 2000, or Windows XP must be installed on the PC. The version of the Windows OS installed on your PC may be determined by clicking on the “System” icon in the Control Panel. ...
Page 8
Getting started 1.4 Hardware installation Figure 1 shows the location of the main components of the evaluation board. The schematic drawing is given in Figure 1. Evaluation board layout Trimmer SW4=Reset SDIP32 socket USB connector & supply 1.4.1 Power supply ...
Page 9
UM0068 Figure 2. Device selection for analog-to-digital conversion ST7262xxx If you are using the analog trimmer, select the installed ST7 device using jumper W6 as shown in Figure 2. This ties the analog trimmer to the PA0 I/O port of ...
Page 10
Running the USB low speed evaluation board 2 Running the USB low speed evaluation board 2.1 Introduction The USB low-speed evaluation board application consists of two main parts: a HID demonstrator running and the evaluation board itself. ...
Page 11
UM0068 2.2 HID demonstrator 2.2.1 USB enumeration The device selection tabsheet, shown in Available USB HID devices: All the HID devices connected to the PC are displayed in this window. Device information This information, obtained during the enumeration phase, refers ...
Page 12
Running the USB low speed evaluation board Figure 5. HID demonstrator window Red LED Slider Bar (LED brightness) 2.3 Remote wake-up function The remote wake-up function is also supported by the evaluation board. By pressing SW3 (ST7262xxx) or SW2 (ST7263Bxx) ...
Page 13
UM0068 Table 1. Description of evaluation board probing points (continued) Probing point ...
Page 14
Running the USB low speed evaluation board Figure 6. Board schematics + 1 12/ UM0068 PD6 1 PD6 PD5 2 PD5 PD4 3 PD4 PD3 ...
Page 15
UM0068 2.5 Enabling board for ICC communication To enable ICC communication on this board, the connection between the V MCU and the charge pump capacitors (C6 and C7) needs to be cut to allow the programming tool to generate pulses ...
Page 16
... Date 28-Oct-2002 11-Oct-2007 14/15 Revision 1.2 Initial Release Added evaluation board root part number (ST7MDTULS-EVAL). Removed ST72F61 and SDIP42-DIP20 adaptor. Changed ST72F62 and ST72F63B root part numbers into 2.0 ST7262xxx and ST7263Bxx, respectively. Removed reference to supplied C source code for PC executable software, Section 1 ...
Page 17
... UM0068 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...