45300 Parallax Inc, 45300 Datasheet - Page 99
![BOARD PROTO SX48](/photos/9/25/92507/mfg_45300_sml.jpg)
45300
Manufacturer Part Number
45300
Description
BOARD PROTO SX48
Manufacturer
Parallax Inc
Type
MCUr
Specifications of 45300
Contents
Board
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With/related Products
SX48
For Use With
130-28029 - KIT PARTS SMART SENSORS45111 - MANUAL FOR SX-KEY/BLITZ VER. 2.028850 - CARRIER BOARD BOARD OF EDU USB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
453001
Manufacturer:
LITTELFUSE/力特
Quantity:
20 000
Company:
Part Number:
453002
Manufacturer:
LITTELFU
Quantity:
1 000
10.4 All About Interrupts
The SX20/28 chip allows for up to nine sources of interrupts; eight external and one internal. The
SX48/52 chip allows for up to 17 sources of interrupts; 10 external and one internal. Any or all of the
port B I/O pins can be configured as external interrupts. See Chapter 10.2.6 – Wakeup (Interrupt) on
Edge Detection for information on configuring external interrupts. The internal interrupt can be
configured to occur upon a rollover condition within the Real Time Clock Counter (RTCC) register. A
special return-from-interrupt command may also be used to adjust the value of the RTCC to cause
interrupts to occur at a specific time interval. See section 10.4.1 for more information.
In addition to the interrupts supported by the SX20/28, with the SX48/52 devices, six different internal
interrupts can be configured for the Timer 1 and Timer 2 overflow and R1/R2 counter comparison reg-
isters.
These interrupt options can be very powerful features but can also cause havoc if not configured or
understood properly. If using interrupts of any kind is desired, the following items should be reviewed.
Interrupt Vector: The interrupt vector in the SX chip points to address $0 and is not configurable. The
interrupt routine must reside at location $0 to be properly executed upon an interrupt event.
Auto Interrupt Disable: As soon as an interrupt occurs, additional interrupts are automatically
ignored by the SX chip until the interrupt routine is completed. This prevents the interrupt routine
from being interrupted and prevents the loss of return vector data. This is also one of the most
important considerations when working with interrupts; you can not immediately (without jitter)
process more than one interrupt at a time.
Note: Should additional interrupts occur, the SX chip does not automatically queue up interrupts for future
processing. See Interrupt Queuing, below, for more information.
Latency Delays: When an interrupt occurs, there is a latency delay before the interrupt routine is
actually activated. For the internal RTCC rollover, this latency is exactly 3 clock cycles in Turbo
mode and 8 clock cycles in Compatible mode. For the external interrupts, the latency delay is
exactly 5 clock cycles in Turbo mode and 10 clock cycles in Compatible mode. Latency may vary by
as much as +1 instruction cycle when interrupting on external asynchronous events, thus a high
clock speed may be necessary to lessen the effects.
Interrupt Routine Size: Normally it is a requirement for an application to process every interrupt
without missing any. To ensure this happens, the longest path through the interrupt routine must
take less time than the shortest possible delay between interrupts.
Interrupt Queuing: If an external interrupt occurs during the interrupt routine, the pending register
will be updated but the trigger will be ignored unless interrupts had first been turned off at the
beginning of the routine and turned on again at the end. This also requires that the new interrupt
doesn’t occur before interrupts are turned off in the interrupt routine. If there is a possibility of
extra interrupts occurring before they can be disabled, the SX will miss those interrupt triggers.
10 SX Special Features and Coding Tips
SX-Key/Blitz Development System Manual 2.0 Parallax, Inc. Page 99