STEVAL-MKI064V1 STMicroelectronics, STEVAL-MKI064V1 Datasheet - Page 31
![BOARD ADAPTER LSM303DLH DIL24](/photos/37/60/376030/image_steval-mki064v1_sml.jpg)
STEVAL-MKI064V1
Manufacturer Part Number
STEVAL-MKI064V1
Description
BOARD ADAPTER LSM303DLH DIL24
Manufacturer
STMicroelectronics
Series
MEMSr
Datasheets
1.STEVAL-MKI009V1.pdf
(42 pages)
2.STEVAL-MKI063V1.pdf
(47 pages)
3.STEVAL-MKI064V1.pdf
(4 pages)
Specifications of STEVAL-MKI064V1
Sensor Type
Accelerometer and Magnetometer
Sensing Range
±2g, 4g, 8g, ±1.3 ~ 8.1 gauss
Interface
I²C
Sensitivity
1 ~ 3.9 mg/Digit, ±0.01%/°C
Embedded
No
Utilized Ic / Part
LSM303DLH
Sensing Axis
Double Axis
Output Type
Digital
Interface Type
USB
For Use With
497-10682 - MOTEHRBOARD MEMS ADAPTER STM32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
LPR5xxxAL, LPY5xxxAL, LY5xxxAL
Other names
497-10689
LSM303DLH
9.1.3
internal registers related to trimming functions to permit good device behavior. If, for any
reason, the content of the trimming registers was changed, it is sufficient to use this bit to
restore the correct values. When the BOOT bit is set to ‘1’ the content of internal Flash is
copied to the corresponding internal registers and is used to calibrate the device. These
values are factory-trimmed and are different for every accelerometer. They permit good
device behavior and normally do not have to be modified. At the end of the boot process, the
BOOT bit is again set to ‘0’.
Table 24.
HPCF[1:0]. These bits are used to configure the high-pass filter cut-off frequency f
given by:
The equation can be simplified to the following approximated equation:
Table 25.
CTRL_REG3_A (22h)
Table 26.
HPcoeff2,1
IHL
00
01
10
11
HPM1
0
0
1
High-pass filter mode configuration
High-pass filter cut-off frequency configuration
CTRL_REG3_A register
Data rate = 50 Hz
PP_OD
f
0.125
t
0.25
0.5
[Hz]
1
HPM0
LIR2
0
1
0
Doc ID 16941 Rev 1
Data rate = 100 Hz
f
I2_CFG1
t
Normal mode (reset reading HP_RESET_FILTER)
Reference signal for filtering
Normal mode (reset reading HP_RESET_FILTER)
=
f
f
t
0.25
ln
t
0.5
[Hz]
2
1
⎛
⎝
=
1
--------------------- -
6
–
⋅
----------- -
HPc
f
1
I2_CFG0
HPc
s
⎞
⎠
⋅
Data rate = 400 Hz
High-pass filter mode
------
2π
f
s
f
t
[Hz]
LIR1
8
4
2
1
Registers description
I1_CFG1
Data rate = 1000 Hz
f
t
2.5
[Hz]
20
10
5
I1_CFG0
t
,which is
31/47