STEVAL-IFS003V1 STMicroelectronics, STEVAL-IFS003V1 Datasheet - Page 20

• Manufacturer Part Number: STEVAL-IFS003V1
• Description: BOARD STLM75/STDS75/ST72F651
• Manufacturer: STMicroelectronics

Specifications of STEVAL-IFS003V1

• Design Resources: STEVAL-IFS003V1 Gerber Files STEVAL-IFS003V1 Schematic STEVAL-IFS003V1 Bill of Materials
• Sensor Type: Temperature
• Sensing Range: -55°C ~ 125°C
• Interface: I²C
• Voltage - Supply: 7.5 V ~ 19 V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ST72F651, STDS75, STLM75
• Silicon Manufacturer: ST Micro
• Silicon Core Number: STLM75/STDS75 And ST72F651AR6
• Kit Application Type: Sensing - Temperature
• Application Sub Type: Temperature Sensor
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensitivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6238

ST72651AR6
4 FLASH PROGRAM MEMORY
4.1 Introduction
The ST7 dual voltage High Density Flash
(HDFlash) is a non-volatile memory that can be
electrically erased as a single block or by individu-
al sectors and programmed on a Byte-by-Byte ba-
sis using an external V
The HDFlash devices can be programmed and
erased off-board (plugged in a programming tool)
or on-board using ICP (In-Circuit Programming) or
IAP (In-Application Programming).
The array matrix organisation allows each sector
to be erased and reprogrammed without affecting
other sectors.
4.2 Main Features
■
■
■
■
4.3 Structure
The Flash memory is organised in sectors and can
be used for both code and data storage.
Figure 11. Memory Map and Sector Address
20/161
1
– Insertion in a programming tool. In this mode,
– ICP (In-Circuit Programming). In this mode, all
– IAP (In-Application Programming) In this
Three Flash programming modes:
ICT (In-Circuit Testing) for downloading and
executing user application test patterns in RAM
Read-out protection
Register Access Security System (RASS) to
prevent accidental programming or erasing
all sectors including option bytes can be pro-
grammed or erased.
sectors including option bytes can be pro-
grammed or erased without removing the de-
vice from the application board.
mode, all sectors except Sector 0, can be pro-
grammed or erased without removing the de-
vice from the application board and while the
application is running.
DFFFh
BFFFh
D7FFh
EFFFh
FFFFh
3FFFh
7FFFh
9FFFh
1000h
4K
PP
8K
supply.
2 Kbytes
10K
8 Kbytes
16K
Doc ID 7215 Rev 4
4 Kbytes
4 Kbytes
16 Kbytes
24K
Depending on the overall Flash memory size in the
microcontroller device, there are up to three user
sectors (see
be erased independently to avoid unnecessary
erasing of the whole Flash memory when only a
partial erasing is required.
The first two sectors have a fixed size of 4 Kbytes
(see
part of the ST7 addressing space so the reset and
interrupt vectors are located in Sector 0 (F000h-
FFFFh).
Table 5. Sectors available in Flash devices
4.4 Read-out Protection
Read-out protection, when selected, provides a
protection against Program Memory content ex-
traction and against write access to Flash memo-
ry. Even if no protection can be considered as to-
tally unbreakable, the feature provides a very high
level of protection for a general purpose microcon-
troller.
In Flash devices, this protection is removed by re-
programming the option. In this case, the entire
program memory is first automatically erased and
the device can be reprogrammed.
Read-out protection selection is enabled and re-
moved through the FMP_R bit in the option byte.
24 Kbytes
Flash Memory Size
32K
Figure
(bytes)
> 8K
4K
8K
40 Kbytes 52 Kbytes
11). They are mapped in the upper
Table
48K
5). Each of these sectors can
60K
Available Sectors
Sectors 0,1, 2
DV FLASH
MEMORY SIZE
SECTOR 2
SECTOR 1
SECTOR 0
Sectors 0,1
Sector 0