SSL2102T/DB/FLYB120V,598 NXP Semiconductors, SSL2102T/DB/FLYB120V,598 Datasheet - Page 11

• Manufacturer Part Number: SSL2102T/DB/FLYB120V,598
• Description: KIT SSL2102 DESIGNER 120V
• Manufacturer: NXP Semiconductors

Specifications of SSL2102T/DB/FLYB120V,598

• Current - Output / Channel: 400mA ~ 1.05A
• Outputs And Type: 1, Isolated
• Voltage - Output: 9 ~ 23 V
• Features: Dimmable
• Voltage - Input: 85 ~ 276VAC
• Utilized Ic / Part: SSL2102
• Duty Cycle (max): 75 %
• Mounting Style: SMD/SMT
• Switching Frequency: 100 KHz
• Operating Supply Voltage: 8.5 V to 40 V
• Supply Current: 1.7 A
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Output Power: 1.6 W
• Package / Case: SOIC-20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-4931

NXP Semiconductors
8. Board optimization
UM10386
User manual
8.1 Changing the output voltage and LED current
8.2 Changing the output ripple current
8.3 Adapting to high power reverse phase (transistor) dimmers.
The following modifications must be made in order to meet different customer application
requirements:
Remark: All components referred to in the text can be located on
schematic
Compared to other topologies, a flyback converter has the major advantage that it is
suitable for driving a broader range of output voltages. Essentially, changing the winding
ratio whilst maintaining the value of the primary inductance, will shift the output working
voltage accordingly. Part of the efficiency of the driver is linked to the output voltage. A
lower output voltage will increase the transformation ratio, and cause higher secondary
losses. In practice, a mains dimmable flyback converter will have an efficiency of between
80 % for high output voltages (such as 60 V) down to 50 % for low output voltages (such
as 3 V). Synchronous rectification might become advisable to reduce losses at low
voltages. The NXP Semiconductors TEA1791 can be used for this purpose. For exact
calculations of transformer properties and peak current, refer to application note
AN10754, “SSL2101 dimmable mains LED driver”, and the calculation tool that is
provided with it.
The output current ripple is principally determined by the LED voltage, the LED dynamic
resistance and the output capacitor. The value of C6 has been chosen to optimize
capacitor size with light output. A ripple of ± 25 % will result in an anticipated deterioration
of light output of <1 %.
The size for the buffer capacitor can be estimated using the following equation:
Example:
For a ripple current of ± 5%, and a mains frequency of 50 Hz, and a dynamic resistance of
0.6 Ω, C6 has to be 20 ÷ (300 × 0.6) = 111 mF. For a ripple current of 25 % and a dynamic
resistance of 6 Ω, C6 has to be 4 ÷ (300 × 6) = 2200 μF. Using a series of LEDs, the
dynamic resistance of each LED can be added to the total dynamic resistance.
Reverse phase (transistor) dimmers differ in two ways that can be beneficial but can also
cause problems with dimming detection:
C
•
out
The negative phase-cut (trailing edge) causes no inrush current when the dimmer
triggers. When using triac dimmers, there will be a sudden voltage difference over the
input leading to a steep charge of the input capacitors. The resultant peak current will
lead to higher damper dissipation. Because this steep charge is missing, the input
capacitors will have less stress, and the input circuit is less prone to audible noise.
=
I
---------- -
LED
I Δ
diagram”.
×
--------------------------------------------
6
All information provided in this document is subject to legal disclaimers.
×
f
net
×
1
Rev. 1 — 1 February 2011
R
dynamic
SSL2102 19 W to 22 W mains dimmable LED driver
Figure 8 “Board
UM10386
© NXP B.V. 2011. All rights reserved.
11 of 24
(1)