STEVAL-ISA051V1 STMicroelectronics, STEVAL-ISA051V1 Datasheet - Page 45
![BOARD EVAL PM6670S DDR2/3](/photos/9/13/91334/steval-isa051v1_sml.jpg)
STEVAL-ISA051V1
Manufacturer Part Number
STEVAL-ISA051V1
Description
BOARD EVAL PM6670S DDR2/3
Manufacturer
STMicroelectronics
Type
DC/DC Switching Converters, Regulators & Controllersr
Specifications of STEVAL-ISA051V1
Design Resources
STEVAL-ISA051V1 Gerber Files STEVAL-ISA051V1 Schematic STEVAL-ISA051V1 Bill of Material
Main Purpose
Special Purpose DC/DC, DDR Memory Supply
Outputs And Type
4, Non-Isolated
Voltage - Output
1.5V, 1.8V
Voltage - Input
4.5 ~ 28V
Regulator Topology
Buck
Board Type
Fully Populated
Utilized Ic / Part
PM6670
Input Voltage
4.5 V to 28 V
Output Voltage
1.8 V, 1.5 V
Product
Power Management Modules
Silicon Manufacturer
ST Micro
Silicon Core Number
PM6670S
Kit Application Type
Power Management
Application Sub Type
DDR2/3 Memory Power Supply Controller
Kit Contents
Board
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Power - Output
-
Frequency - Switching
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
PM6670S
Other names
497-8411
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STEVAL-ISA051V1
Manufacturer:
STMicroelectronics
Quantity:
1
PM6670S
where R
Switching losses are approximately given by:
Equation 41
where t
gate-driver current capability and the gate charge Q
low R
As general rule, the R
MOSFET.
Logic-level MOSFETs are recommended, as long as low-side and high-side gate drivers are
powered by V
greater than the maximum input voltage.V
Table 16
Table 16.
In buck converters the power dissipation of the synchronous MOSFET is mainly due to
conduction losses:
Equation 42
Maximum conduction losses occur at the maximum input voltage:
Equation 43
The synchronous rectifier should have the lowest R
MOSFET turns on, high d
through its gate-drain capacitance C
the choice of the low-side MOSFET is a trade-off between on resistance and gate charge; a
good selection should minimize the ratio C
Equation 44
Manufacturer
DSon
ON
P
DSon
ST
IR
lists tested high-side MOSFETs.
switching
. Unfortunately low R
and t
Evaluated high-side MOSFETs
is the drain-source on-resistance of the control MOSFET.
VCC
OFF
=
= +5 V. The breakdown voltage of the MOSFETs (V
V
are the turn-on and turn-off times of the MOSFET and depend on the
IN
DSon
STS12NH3LL
⋅
I (
IRF7811
LOAD
P
V
Type
conduction
x Q
/d
t
(max)
of the phase node can bring up even the low-side gate
Doc ID 14432 Rev 4
gate
DSon
2
product should be minimized to find out the suitable
=
−
P
R
MOSFETs have a great gate charge.
RRS
C
DLowSide
Δ
DSon
2
GS
I
L
, causing a cross-conduction problem. Once again,
)
=
⋅
R
INmax
(mΩ)
⋅
RSS
t
10.5
DSon
⎛
⎜
⎜
⎝
C
on
9
1
≅
ISS
−
⋅
P
/ C
f
.
sw
V
conduction
−
V
IN
GS
OUT
C
+
,
MAX
gate
DSon
RSS
V
where
IN
. A greater efficiency is achieved with
⎞
⎟
⎟
⎠
⋅
⋅
as possible. When the high-side
I (
Gate charge
I
LOAD
LOAD
(nC)
12
18
,
MAX
(max)
2
Application information
2
+
BRDSS
Δ
2
I
L
)
⋅
Rated reverse
t
) must be
off
voltage (V)
⋅
f
sw
30
30
45/54