ADC08500DEV/NOPB National Semiconductor, ADC08500DEV/NOPB Datasheet - Page 14

• Manufacturer Part Number: ADC08500DEV/NOPB
• Description: BOARD DEV FOR ADC08D500
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of ADC08500DEV/NOPB

• Number Of Adc's: 1
• Number Of Bits: 8
• Sampling Rate (per Second): 500M
• Data Interface: Serial
• Inputs Per Adc: 1 Differential
• Input Range: 870 mVpp
• Power (typ) @ Conditions: 800mW @ 500MSPS
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: ADC08500
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: ADC08500DEV

9.1 Installing the WaveVision
9.2 Java™ Technology
The
Microsystems
Java software must be installed on the computer
in order for the WaveVision software to run. The
software can run on top of either the Java
Runtime
Development Kit (JDK), Version 1.4 or higher. A
suitable copy of the JRE is included on the
WaveVision CD-ROM.
The WaveVision installer will first search for an
existing copy of the JRE or JDK on the computer.
If neither is found, the installer will prompt you to
first install a JRE.
J2RE*.exe installer program which may be
found on the CD-ROM.
instructions to finish the install.
After a suitable JRE or JDK is installed, run the
WaveVision installer again.
detect the Java software and configure the
WaveVision software to use it.
Java technology can allow software to run on
different platforms.
software contains Windows-specific hardware
interface code and is therefore only supported
under Windows.
9.0
1. Insert the WaveVision CD-ROM into the
2. The WaveVision software requires a
3. Locate
4. Follow the on-screen instructions to
Appendix B - Installing and
running the WaveVision4
software
Software
WaveVision
computer’s CD-ROM drive.
Java
Development Kit, Version 1.4 or higher,
from Sun Microsystems, Inc. For detailed
information on WaveVision’s use of Java
technology, see Section 10.2. If the
computer does not have this software,
the WaveVision installer will instruct you
on how to install it.
Setup.exe program on the CD-ROM.
finish the install
Environment
Runtime Environment or Java
Java technology. The underlying
and
However, the WaveVision
.
run
software
To do this, run the
(JRE)
Follow the on-screen
the
The installer will
or
WaveVision4
uses
the
Figure 15. WaveVision plot tools
Java
Sun
9.3 Automatic Device Detection and
The WaveVision system provides automatic
hardware detection and configuration for the
device under test. The FPGA is re-programmed
automatically
Development board is turned on.
Normally, the configuration process is completely
transparent
intervention. However, this process can be
overridden, if required, by specifying a new Xilinx
configuration image. To do this, select the Xilinx
Image Settings button (Figure 14) within the
Capture Setting window (Settings ? Capture
Settings).
9.4 Windows Driver
The WaveVision software communicates with the
WaveVision hardware through the Windows
device driver software. If you are unable to
connect to the WaveVision board after installing
the software, do the following to uninstall and
reinstall the driver:
The WaveVision software provides several tools
to manipulate the plot view. A toolbar appears
above each plot, similar to Figure 15.
10.0 Appendix C - Using
1. Find the Windows Control Panel and
2. Click on Device Manager and scroll down
3. With the WaveVision board connected, an
4. Right click on the unknown device and
5. Unplug the USB cable from the board.
6. Plug in USB cable to the board again to
WaveVision Plots
select System. If you are using Windows
2000/XP, select the Hardware tab.
to the Universal Serial Bus controllers.
unknown device will be listed.
uninstall the driver.
reinstall the driver
Configuration
Figure 14. Selecting Xilinx image settings
to
by
the
the
user
.
host
and
PC
requires
when
the
no
14