DS26524DK Maxim Integrated Products, DS26524DK Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS26524DK
Manufacturer Part Number
DS26524DK
Description
KIT DESIGN FOR DS26524
Manufacturer
Maxim Integrated Products
Datasheet
1.DS26524G.pdf
(273 pages)
Specifications of DS26524DK
Main Purpose
Telecom, Framer and Line Interface Units (LIUs)
Utilized Ic / Part
DS26524
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Secondary Attributes
-
Embedded
-
Primary Attributes
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 32 of 273
- Download datasheet (3Mb)
8.8.1.1 Elastic Stores Initialization
There are two elastic store initializations that can be used to improve performance in certain applications: elastic
store reset and elastic store align. Both of these involve the manipulation of the elastic store’s read and write
pointers and are useful primarily in synchronous applications (RSYSCLK/TSYSCLK are locked to RCLK/TCLK,
respectively). The elastic store reset is used to minimize the delay through the elastic store. The elastic store align
bit is used to “center” the read/write pointers to the extent possible.
Table 8-3. Elastic Store Delay After Initialization
Receive Elastic Store Reset
Transmit Elastic Store Reset
Receive Elastic Store Align
Transmit Elastic Store Align
N = 9 for RSZS = 0; N = 2 for RSZS = 1.
8.8.1.2 Minimum Delay Mode
Elastic store minimum-delay mode can be used when the elastic store’s system clock is locked to its network clock
(i.e., RCLK locked to RSYSCLK for the receive side and TCLK locked to TSYSCLK for the transmit side).
RESCR.1 enables the receive elastic store minimum-delay mode. When enabled, the elastic stores are forced to a
maximum depth of 32 bits instead of the normal two-frame depth. This feature is useful primarily in applications that
interface to a 2.048MHz bus. Certain restrictions apply when minimum-delay mode is used. In addition to the
restriction mentioned above, RSYNC must be configured as an output when the receive elastic store is in
minimum-delay mode and TSYNC must be configured as an output when transmit minimum-delay mode is
enabled. In this mode the SYNC outputs are always in frame mode (multiframe outputs are not allowed). In a
typical application, RSYSCLK and TSYSCLK are locked to RCLK and RSYNC (frame-output mode) is connected to
TSSYNCIO (frame-input mode). The slip zone select bit (RSZS at RESCR.4) must be set to 1. All the slip
contention logic in the framer is disabled (since slips cannot occur). On power-up, after the RSYSCLK and
TSYSCLK signals have locked to their respective network clock signals, the elastic store reset bit (RESCR.2)
should be toggled from a 0 to 1 to ensure proper operation
8.8.1.3 Additional Receive Elastic Store Information
If the receive-side elastic store is enabled, the user must provide either a 1.544MHz or 2.048MHz clock at the
RSYSCLK pin. See Section
providing a frame/multiframe sync at the RSYNC pin or having the RSYNC pin provide a pulse on frame/multiframe
boundaries. If signaling reinsertion is enabled, the robbed-bit signaling data is realigned to the multiframe sync
input on RSYNC. Otherwise, a multiframe sync input on RSYNC is treated as a simple frame boundary by the
elastic store. The framer always indicates frame boundaries on the network side of the elastic store via the
RFSYNC output, whether the elastic store is enabled or not. Multiframe boundaries arel always indicated via the
RMSYNC output. If the elastic store is enabled, RMSYNC outputs the multiframe boundary on the backplane side
of the elastic store. When the device is receiving T1 and the backplane is enabled for 2.048MHz operation, the
RMSYNC signal outputs the T1 multiframe boundaries as delayed through the elastic store. When the device is
receiving E1 and the backplane is enabled for 1.544MHz operation, the RMSYNC signal outputs the E1 multiframe
boundaries as delayed through the elastic store.
If the user selects to apply a 2.048MHz clock to the RSYSCLK pin, the user can use the Receive Blank Channel
Select registers (RBCS1:RBCS4) to determine which channels will have the data output at RSER forced to all
ones.
INITIALIZATION
8.8.2
for higher rate system-clock applications. The user has the option of either
REGISTER BIT
RESCR.2
RESCR.3
TESCR.2
TESCR.3
32 of 273
N bytes < Delay < 1 Frame + N bytes
N bytes < Delay < 1 Frame + N bytes
1/2 Frame < Delay < 1 1/2 Frames
1/2 Frame < Delay < 1 1/2 Frames
DELAY
Related parts for DS26524DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: