KS8842-16MQL-EVAL Micrel Inc, KS8842-16MQL-EVAL Datasheet - Page 49
KS8842-16MQL-EVAL
Manufacturer Part Number
KS8842-16MQL-EVAL
Description
EVAL KIT EXPERIMENTAL KS8842
Manufacturer
Micrel Inc
Datasheet
1.KS8842-16MQL-EVAL.pdf
(141 pages)
Specifications of KS8842-16MQL-EVAL
Main Purpose
Interface, Ethernet
Utilized Ic / Part
KS8842
Lead Free Status / RoHS Status
Not applicable / Not applicable
Secondary Attributes
-
Embedded
-
Primary Attributes
-
Lead Free Status / Rohs Status
Not Compliant
- Current page: 49 of 141
- Download datasheet (764Kb)
The format for ConfigParam is shown in Table 13.
Loopback Support
The KSZ8842M provides loopback support for remote diagnostic of failure. In loopback mode, the speed at both PHY
ports will be set to 100BASE-TX full-duplex mode. Two types of loopback are supported: Far-end Loopback and Near-end
(Remote) Loopback.
Far-end Loopback
Far-end loopback is conducted between the KSZ8842M’s two PHY ports. The loopback path starts at the “Originating.”
PHY port’s receive inputs (RXP/RXM), wraps around at the “loopback” PHY port’s PMD/PMA, and ends at the
“Originating” PHY port’s transmit outputs (TXP/TXM).
Bit [8] of registers P1CR4 and P2CR4 is used to enable far-end loopback for ports 1 and 2, respectively. Alternatively, Bit
[14] of registers P1MBCR and P2MBCR can also be used to enable far-end loopback. The port 2 far-end loopback path is
illustrated in the Figure 15.
Near-end (Remote) Loopback
Near-end (Remote) loopback is conducted at either PHY port 1 or PHY port 2 of the KSZ8842M. The loopback path starts
at the PHY port’s receive inputs (RXPx/RXMx), wraps around at the same PHY port’s PMD/PMA, and ends at the PHY
port’s transmit outputs (TXPx/TXMx).
Bit [1] of registers P1PHYCTRL and P2PHYCTRL is used to enable near-end loopback for ports 1 and 2, respectively.
Alternatively, Bit [9] of registers P1SCSLMD and P2SCSLMD can also be used to enable near-end loopback. The both
ports 1 and 2 near-end loopback paths are illustrated in the following Figure 16.
Micrel, Inc.
October 2007
Bit
15 -2
1
0
Bit Name
Reserved
Clock_Rate
ASYN_8bit
Description
Reserved
Internal clock rate selection
0: 125 MHz
1: 25 MHz
Note: At power up, this chip operates on 125 MHz clock. The internal frequency can be
dropped to 25 MHz via the external EEPROM.
Async 8-bit or 16-bit bus select
1= bus is configured for 16-bit width
0= bus is configured for 8-bit width
(32-bit width, KSZ8842-32, don’t care this bit setting)
Table 13. ConfigParam Word in EEPROM Format
49
KSZ8842-16/32 MQL/MVL/MVLI/MBL
M9999-102207-1.9
Related parts for KS8842-16MQL-EVAL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC SWITCH 10/100 16BIT 128PQFP
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
IC SWITCH 10/100 32BIT 128PQFP
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Micrel Inc
Datasheet: