STEVAL-ISB009V1 STMicroelectronics, STEVAL-ISB009V1 Datasheet - Page 10
![BOARD EVAL BATT MONITOR STC3100](/photos/9/9/90935/steval-isb009v1_sml.jpg)
STEVAL-ISB009V1
Manufacturer Part Number
STEVAL-ISB009V1
Description
BOARD EVAL BATT MONITOR STC3100
Manufacturer
STMicroelectronics
Type
Battery Managementr
Datasheets
1.STC3100IQT.pdf
(21 pages)
2.STEVAL-ISB009V1.pdf
(4 pages)
3.STEVAL-ISB009V1.pdf
(9 pages)
Specifications of STEVAL-ISB009V1
Main Purpose
Power Management, Battery Monitor
Embedded
No
Utilized Ic / Part
STC3100
Primary Attributes
Monitors Current, Voltage, Temperature
Secondary Attributes
Includes Coulomb Counter for Charge/Discharge Status
Board Size
23 mm x 18 mm
Interface Type
I2C
Product
Power Management Modules
Dimensions
23 mm x 18 mm
Lead Free Status / RoHS Status
Lead free by exemption / RoHS compliant by exemption
For Use With/related Products
STC3100
Other names
497-10045
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STEVAL-ISB009V1
Manufacturer:
STMicroelectronics
Quantity:
2
Functional description
7.2
7.3
7.4
10/21
The conversion cycle for n bit resolution is 2
clock, the conversion cycle time is 125 to 500 ms for a 12- to 14-bit resolution. The LSB
value is set by the internal gain and internal reference and is 11.77 uV at maximum
resolutions. When using an external 30 milliOhms sense resistor, the 28-bit accumulator
results in a capacity of approximately +/- 7300 mA.h. The upper 16 bits of the accumulator
can be read from the I2C interface, giving a resolution of 0.2 mA.h.
When the battery voltage falls below the under voltage lockout threshold at 2.7 V, the gas
gauge system is stopped and the STC3100 stays in standby mode with minimum quiescent
current. All registers are maintained down to 2.0 V. Below 2.0 V, the registers are reset to
their default power-on value.
The gas gauge system needs an accurate 32,768 Hz timebase to compute the level of
charge flowing from/to the battery. The STC3100 can operate from an internal oscillator, or
use an external RTC signal for highest accuracy.
Battery voltage and temperature monitoring
The battery voltage and chip temperature (close to the battery temperature) are measured
by means of an A/D converter and a multiplexer. This function takes place concurrently to
the gas gauge function with a dedicated A/D converter, which means that it does not affect
the performance of the gas gauge. To reduce the power consumption, a conversion takes
place only every two seconds, alternatively for battery voltage and temperature (so each
value is refreshed every four seconds).
The conversion cycle takes 2
conversion cycle time is 250 ms. The resolution is 2.44 mV for the battery voltage and
0.125° C for the temperature.
General-purpose input/output
A general-purpose I/O line is available. The output is an open drain, and an external pull-up
resistor may be needed in the application. Writing the IO0DATA bit to 0 forces the IO0 output
low; writing the IO0DATA bit to 1 leaves the IO0 output in a high impedance state. Reading
the IO0DATA bit gives the state of the IO0 pin.
In standby (CG_RUN=0), reset (PORDET set to 1) and power-down (Vcc<UVLOth) states,
the IO0 output is open and the input is read as zero whatever is the actual state of the IO0
pin.
RAM registers
The STC3100 provides 32 RAM registers to store any information regarding battery status,
charge cycles, battery aging, proprietary informations, etc...
The register content is maintained during standby and low voltage states, down to the
power-on reset level of approximately 2.0 V. Below this level, the content is not preserved.
This usually means that the Li-Ion cell was very deeply discharged and has been damaged.
13
= 8192 clock cycles. Using the 32,768 Hz internal clock, the
n
clock cycles. Using the 32,768 Hz internal
STC3100