ZUP36-24/U TDK Corporation, ZUP36-24/U Datasheet - Page 45

• Manufacturer Part Number: ZUP36-24/U
• Description: PWR SUP BENCH PROG 0-36V 864W
• Manufacturer: TDK Corporation
• Series: ZUPr
• Type: Programmabler

Specifications of ZUP36-24/U

• Load Regulation: 0.07%
• Voltage - Output: 0 ~ 36V
• Number Of Outputs: 1
• Power (watts): 864W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 0 ~ 36 VDC @ 24A
• Size / Dimension: 13.78" L x 5.51" W x 4.88" H (350mm x 140mm x 124mm)
• Power (watts) - Rated: 864W
• Operating Temperature: 0°C ~ 50°C
• Efficiency: 84%
• Approvals: CE, EN, UL
• Line Regulation: 0.01%
• Power Supply Output Type: Variable
• No. Of Outputs: 1
• Output Voltage: 36V
• Output Current: 24A
• Power Rating: 864W
• Input Voltage: 85V AC To 265V AC
• Length: 350mm
• Width: 140mm
• Accuracy: 0.02% + 20 mV
• Brand/series: ZUP
• Current, Output: 24 A
• Display Type: Digital Meter
• Power, Output: 864 W
• Power, Rating: 864 W (Max.)
• Regulation, Line: 0.01% + 5 mA⁄1 mV + 0.005%
• Regulation, Load: 0.07% + 7 mA⁄2 mV + 0.005%
• Standards: UL Listed, CE Marked
• Temperature Coefficient: 30 ppm⁄°C (CV)⁄100 ppm⁄°C (CC)
• Temperature, Operating, Maximum: 50 °C
• Temperature, Operating, Minimum: 0 °C
• Voltage, Input: 85-265 VAC
• Voltage, Noise: 70 mV @ 20 MHz BW
• Voltage, Output: 36 VDC
• Voltage, Ripple: 5 mV @ 5 Hz to 1 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1677; ZUP3624/U

5.3
5.3.1 Introduction
Fig. 5-1: Linking ZUP units with RS232 control.
5.3.2 Rear panel connectors pinout
OUT
The RS232 interface is accessible through the rear panel IN/OUT jacks. The jacks are 8 contacts each
and conform to EIA/TIA-568A requirements. The IN and OUT jacks are used to connect the units in a
RS232 or RS458 chain to a controller. The data format is ASCII, 8 bits/character no parity bit, one stop bit.
The baud rate can be selected to one of the 6 possible rates between 300 and 9600bps (refer to
par.5.2.3).Rrefer to par.5.6 for detailed explanation.
Up to 31 ZUP units can be connected to the RS232 control as shown in Fig.5-1.
IN
Tx and Rx are used for RS232 communication. Txd +/- and Rxd +/- are used for RS485
communication. Refer to RS232 and RS485 cables description for connection details.
REMOTE PROGRAMMING VIA RS232
10m max.
RS232
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Shield (connector enclosure)
ZUP (1)
TXD
TXD
TXD
TXD
RXD +
RXD
RXD +
RXD
+
+
_
_
1000m max.
_
_
RS485
TX(RS232)
SG
NC
SG
Not used
RX (RS232)
Not used
NC
NOTE
ZUP (2)
Fig. 5-2:
Rear panel connector pinout
RS485
(ZUP rear panel view)
ZUP (31)