ZUP36-24/U TDK Corporation, ZUP36-24/U Datasheet - Page 38

• Manufacturer Part Number: ZUP36-24/U
• Description: PWR SUP BENCH PROG 0-36V 864W
• Manufacturer: TDK Corporation
• Series: ZUPr
• Type: Programmabler

Specifications of ZUP36-24/U

• Load Regulation: 0.07%
• Voltage - Output: 0 ~ 36V
• Number Of Outputs: 1
• Power (watts): 864W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 85 ~ 265VAC
• Mounting Type: Chassis Mount
• 1st Output: 0 ~ 36 VDC @ 24A
• Size / Dimension: 13.78" L x 5.51" W x 4.88" H (350mm x 140mm x 124mm)
• Power (watts) - Rated: 864W
• Operating Temperature: 0°C ~ 50°C
• Efficiency: 84%
• Approvals: CE, EN, UL
• Line Regulation: 0.01%
• Power Supply Output Type: Variable
• No. Of Outputs: 1
• Output Voltage: 36V
• Output Current: 24A
• Power Rating: 864W
• Input Voltage: 85V AC To 265V AC
• Length: 350mm
• Width: 140mm
• Accuracy: 0.02% + 20 mV
• Brand/series: ZUP
• Current, Output: 24 A
• Display Type: Digital Meter
• Power, Output: 864 W
• Power, Rating: 864 W (Max.)
• Regulation, Line: 0.01% + 5 mA⁄1 mV + 0.005%
• Regulation, Load: 0.07% + 7 mA⁄2 mV + 0.005%
• Standards: UL Listed, CE Marked
• Temperature Coefficient: 30 ppm⁄°C (CV)⁄100 ppm⁄°C (CC)
• Temperature, Operating, Maximum: 50 °C
• Temperature, Operating, Minimum: 0 °C
• Voltage, Input: 85-265 VAC
• Voltage, Noise: 70 mV @ 20 MHz BW
• Voltage, Output: 36 VDC
• Voltage, Ripple: 5 mV @ 5 Hz to 1 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1677; ZUP3624/U

4.4.11 Output Voltage Programming by external voltage
External control connector
Fig. 4-7 shows the set-up for external voltage programming of the output voltage. A voltage source
variable from 0 to 4V, programs the output voltage proportionally from zero to full scale. The static load
current on the programming source is less than 2uA. The source resistance should be less than
10Kohm to avoid degradation of offset and drift specifications. When external voltage is used for
programming the front panel and the computer control (via the serial communication) are disabled.
Note: Full scale is 105% of the rated output voltage.
0~4VDC
External control connector
4.4.12 Output Current Programming by external voltage
0~4VDC
Fig. 4-8 shows the set-up for external voltage programming of the output current. A voltage source
variable from 0 to 4V, programs the output current proportionally from zero to full scale. The static load
current on the programming source is less than 2uA. The source resistance should be less than
10Kohm to avoid degradation of offset and drift specifications.
Note: Full scale is 105% of the rated output current.
Voltage
Voltage
source
source
Avoid connection of resistors greater than 4kohm or voltage greater than 4V for external resistor
or voltage programming, as it may cause the output voltage and current to exceed the power
The Com pin at the external control connector is connected to the -Sense potential. NEVER
supply rating. The display will NOT show the actual voltage and current when such resistor
_
+
_
+
connect the Com pin (pin10) to any potential, as it may damage the power supply.
VCCP
VCVP
RCCP
VCCP
VCVP
RCCP
COM
COM
- S
+S
- S
+S
P
P
or voltage is applied for programming.
14
14
2
2
13
1
13
1
CAUTION
CAUTION
Output Good
On/Off
VRFV
VRFI
RCVP
Output Good
On/Off
VRFV
VRFI
RCVP
- LS
+LS
- LS
+LS
Fig. 4-8:
Output current programming
by external voltage source.
Fig. 4-7:
Output voltage programming
by external voltage source.
(ZUP rear panel view)
(ZUP rear panel view)