AFCT-5745PZ Avago Technologies US Inc., AFCT-5745PZ Datasheet
![TXRX SFF SONET OC48 BAIL SR](/photos/22/52/225249/4532983_sml.jpg)
AFCT-5745PZ
Specifications of AFCT-5745PZ
Related parts for AFCT-5745PZ
AFCT-5745PZ Summary of contents
Page 1
... Hot-plugging is ensured by design and by 3-stage pin sequencing at the electrical interface. Part Number Options The AFCT-5745Z SFP family consists of the following products: Part Link Tempe- Number Distance rature* AFCT-5745PZ 2km Extended AFCT-5745APZ 2km Industrial AFCT-5745TPZ 15km Extended AFCT-5745ATPZ 15km Industrial * Extended Temperature Range is - ...
Page 2
... Transmitter Section Design A schematic diagram for the transmitter is shown in Fig- ure 1. The AFCT-5745xPZ incorporates an FP laser as its optical source, the AFCT-5745xTPZ incorporates an DFB laser as its optical source. All part numbers have been designed to be compliant with IEC 825 and CDRH eye safety requirements ...
Page 3
... VIEWED THROUGH TOP OF BOARD) Figure 2. Connection Diagram of Module Printed Circuit Board 3 Installation The AFCT-5745Z can be installed in or removed from any Multisource Agreement (MSA) –compliant Small Form Pluggable port regardless of whether the host equip- ment is operating or not. The module is simply inserted, electrical interface first, under finger pressure ...
Page 4
... Ω 50 Ω SERDES 4 µF 50 Ω 100 50 Ω PLD 4 4 µH 1 µH 0.1 µF 10 µ AFCT-5745Z 0.1 µF 4 Tx_DISABLE Tx_FAULT 0.1 µF TD+ LASER DRIVER 100 & SAFETY TD– CIRCUITRY TX GND 0.1 µ 0.1 µF 0.1 µF RD+ AMPLIFICATION RD– & QUANTIZATION 0.1 µ ...
Page 5
Table 1. Pin-out Table The pin arrangement and definition of this product meets SFP MSA. Table 1 lists the pin description. Pin Name Function/Description Transmitter Ground EE 2 TX_FAULT Transmitter Fault Indication 3 TX_DISABLE Transmitter Disable - ...
Page 6
... Addresses 68-83 specify the AFCT-5745Z ASCII serial number and will vary on a per unit basis. 5. Addresses 84-91 specify the AFCT-5745Z ASCII date code and will vary on a per date code basis. 6. Module is compatible with both internal and external DMI Calibration math at host end. ...
Page 7
... Table 3. Individual Identifiers AFCT-5745PZ AFCT-5745APZ Notes/ Address Hex ASCII Address 2km 2000m AFCT-5745TPZ Notes/ Hex ASCII Address Hex 11 SR 2km 2000m AFCT-5745ATPZ Notes/ Notes/ ASCII Address Hex ASCII IR IR-1 15km 14 0F 15km 15000m 15 96 15000m ...
Page 8
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 µW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 µW. 6. Bytes 55-94 are not intended from use with AFCT-5745Z, but have been set to default values per SFF-8472. 7. Bytes checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 9
... Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter. 2. AFCT-5745Z does not respond to state changes on Rate Select Input Pin internally hardwired to full bandwidth. Table 6. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117 ...
Page 10
... Input Voltage on any Pin Receiver Optical Input Recommended Operating Conditions Typical operating conditions are those values for which functional performance and device reliability is implied. Parameter Case Operating Temperature AFCT-5745PZ/TPZ AFCT-5745APZ/ATPZ Supply Voltage Transceiver Electrical Characteristics Parameter Module supply current Power Dissipation ...
Page 11
... AFCT-5745TPZ/ATPZ Back Reflection Sensitivity AFCT-5745TPZ/ATPZ Jitter Generation Receiver Optical Characteristics Parameter Receiver Sensitivity Receiver Overload AFCT-5745PZ/APZ AFCT-5745TPZ/ATPZ Input Operating Wavelength LOS - Deasserted LOS - Asserted LOS - Hysteresis Reflectance Notes: 1. The output power is coupled into single mode fiber. Minimum output optical level is at end of life. ...
Page 12
Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics (T = -10 °C to +85 ° Parameter Transceiver Internal Temperature Accuracy Transceiver Internal Supply Voltage Accuracy Transmitter Laser dc Bias ...
Page 13
V > 2. Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_init t-init: TX DISABLE NEGATED V > 2. Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_init INSERTION t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED OCCURANCE OF FAULT Tx_FAULT Tx_DISABLE TRANSMITTED SIGNAL t_fault ...
Page 14
... Avago will be required to meet the require- ments of FCC in the United States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The metal housing and shielded design of the AFCT- 5745Z minimize the EMI challenge facing the host equip- ment designer. These transceivers provide superior EMI performance ...
Page 15
... AVAGO AFCT-5745XXXZ ####nm LASER PROD) COUNTRY OF ORIGIN YYWW (BAR CODE) S/N:######## 21 CFR(J) CLASS1 LABEL 13. 10 ±0.10 0. 516 ±0.004 55. 50 ±0.20 2. 185 ±0.008 8. 45 ±0.10 0. 333 ±0.004 Notes: 1 ...
Page 16
Figure 8. SFP host board mechnical layout 16 ...
Page 17
... Connection of the AFCT-5745Z to a non-approved optical source, operating above the rec- ommended absolute maximum conditions or operating the AFCT-5745Z in a manner inconsistent with its design and function may result in hazardous radiation exposure and may be considered an act of modifying or manufac- turing a laser product. The person(s) performing such an act are required by law to re-certify and re-identify the laser product under the provisions of U ...
Page 18
... Operating case temperature: -10 °C to +85 °C AFCT-5745TPZ IR, Plastic Bail Delatch Operating case temperature: -40 °C to +85 °C AFCT-5745ATPZ IR, Plastic Bail Delatch EEPROM Content and / or Label Options AFCT-5745PZ-YYY SR, Plastic Bail Delatch, -10°C to +85°C AFCT-5745APZ-YYY SR, Plastic Bail Delatch, -40°C to +85°C AFCT-5745TPZ-YYY IR, Plastic Bail Delatch, -10°C to +85°C AFCT-5745ATPZ-YYY IR, Plastic Bail Delatch, -40° ...