AFCT-5964NLZ Avago Technologies US Inc., AFCT-5964NLZ Datasheet - Page 10

• Manufacturer Part Number: AFCT-5964NLZ
• Description: TXRX OPT SM SONET OC3/SDH 2X10
• Manufacturer: Avago Technologies US Inc.
• Series: METRAKr

Specifications of AFCT-5964NLZ

• Applications: General Purpose
• Data Rate: 115Mbps
• Wavelength: 1300nm
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Data Rate Max: 0.155Gbps
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Recommended Solder and Wash Process
The AFCT-5964TLZ/TGZ/ATLZ/ATGZ/NLZ/NGZ
are compatible with industry-standard wave
solder processes.
Process plug
This transceiver is supplied with a process
plug for protection of the optical port within
the LC connector receptacle. This process plug
prevents contamination during wave solder and
aqueous rinse as well as during handling,
shipping and storage. It is made of a high-
temperature, molded sealing material that can
withstand +85 °C, and a rinse pressure of 110
lbs per square inch.
The process plug should only be used once.
After removing it from the transceiver, it must
not be used again as a process plug; however,
if it has not been contaminated, it can be
reused as a dust cover.
Recommended Solder fluxes
S o l d e r
AFCT-5964TLZ//TGZ/ATLZ/ATGZ/NLZ/NGZ
should be water-soluble, organic fluxes.
Recommended solder fluxes include Lonco 3355-
11 from London Chemical West, Inc. of Burbank,
CA, and 100 Flux from Alpha-Metals of Jersey
City, NJ.
Figure 8. Recommended Panel Mounting
10
(0.4 ±0.004)
DIMENSIONS IN MILLIMETERS (INCHES)
1.
2.
10.16 ±0.1
FIGURE DESCRIBES THE RECOMMENDED FRONT PANEL OPENING FOR A LC OR SG SFF TRANSCEIVER.
SFF TRANSCEIVER PLACED AT 15.24 mm (0.6) MIN. SPACING.
14.22 ±0.1
±0.004)
(0.56
15.24
DETAIL A
(0.6)
f l u x e s
TOP OF PCB
15.24
(0.6)
u s e d
B
(0.039)
(0.62 MAX. 0.59 MIN.)
15.75 MAX. 15.0 MIN.
1
A
w i t h
SECTION B - B
SOLDER POSTS
t h e
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane
Other: naphtha.
Do not use partially halogenated hydrocarbons
such as 1,1.1 trichloroethane, ketones such as
MEK, acetone, chloroform, ethyl acetate,
methylene dichloride, phenol, methylene chloride,
or N-methylpyrolldone. Also, Avago Technologies
does not recommend the use of cleaners that
use halogenated hydrocarbons because of their
potential environmental harm.
LC SFF Cleaning Recommendations
In the event of contamination of the optical
ports, the recommended cleaning process is the
use of forced nitrogen.
thought to have remained, the optical ports can
be cleaned using a NTT international Cletop
stick type (diam. 1.25 mm) and HFE7100
cleaning fluid.
B
If contamination is