AFCT-5971ALZ Avago Technologies US Inc., AFCT-5971ALZ Datasheet - Page 11

• Manufacturer Part Number: AFCT-5971ALZ
• Description: TXRX FE SM LASER 125MBS 2X5
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-5971ALZ

• Applications: Ethernet
• Data Rate: 125MBd
• Wavelength: 1300nm
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Data Rate Max: 0.125Gbps
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155Mbps
• Optical Rise Time: 2/2.2ns
• Optical Fall Time: 2/2.2ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1360/1580nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 3.1V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.5V
• Output Current: 50mA
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• Product: Transceiver
• Maximum Rise Time: 2 ns, 2.2 ns
• Maximum Fall Time: 2 ns, 2.2 ns
• Maximum Output Current: 50 mA
• Operating Supply Voltage: 3.1 V to 3.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: DIP-10 with Connector
• Function: Applications specified for signal rate of 125 MBd, for Fast Ethernet, and Singlemode Fiber.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Singlemode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 1: Regulatory Compliance - Targeted Specification
11
Electrostatic Discharge (ESD)
There are two design cases in which immunity to ESD
damage is important.
The first case is during handling of the transceiver prior
to mounting it on the circuit board. It is important to use
normal ESD handling precautions for ESD sensitive de-
vices. These precautions include using grounded wrist
straps, work benches, and floor mats in ESD controlled
areas.
The second case to consider is static discharges to the
exterior of the equipment chassis containing the trans-
ceiver parts. To the extent that the LC connector recep-
tacle is exposed to the outside of the equipment chassis
it may be subject to whatever system-level ESD test cri-
teria that the equipment is intended to meet.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet FCC regulations in the United States, CENELEC
EN55022 (CISPR 22) in Europe and VCCI in Japan. Refer
to EMI section (page 9) for more details.
Immunity
Transceivers will be subject to radio-frequency elec-
tromagnetic fields following the IEC 1000-4-3 test
method.
Eye Safety
These laser-based transceivers are classified as AEL Class
I (U.S. 21 CFR(J) and AEL Class 1 per EN 0825-1 (+A11).
Feature
Electrostatic Discharge (ESD)
to the Electrical Pins
Electrostatic Discharge (ESD)
to the LC Receptacle
Electromagnetic Interference
(EMI)
Immunity
Laser Eye Safety
and Equipment Type Testing
Component
Recognition
Test Method
MIL-STD-883
Method 3015
Variation of IEC 1000-4-2
FCC Class B
Variation of IEC 1000-4-3
FDA CDRH 21-CFR 1040
Class 1
IEC 0825-1
Amendment 2 2001-01
Underwriters Laboratories and
Canadian Standards Association Joint
Component Recognition for Informa-
tion Technology Equipment Includ-
ing Electrical Business Equipment.
They are eye safe when used within the data sheet limits
per CDRH. They are also eye safe under normal operat-
ing conditions and under all reasonably foreseeable
single fault conditions per EN0825-1. Avago Technolo-
gies has tested the transceiver design for compliance
with the requirements listed below under normal
operating conditions and under single fault conditions
where applicable. TUV Rheinland has granted certifica-
tion to these transceivers for laser eye safety and use in
EN 0825-2 applications. Their performance enables the
transceivers to be used without concern for eye safety
up to 3.5 V transmitter V
CAUTION:
There are no user serviceable parts nor any mainte-
nance required for the AFCT-5971LZ/ALZ. All adjust-
ments are made at the factory before shipment to our
customers. Tampering with or modifying the perform-
ance of the parts will result in voided product warranty.
It may also result in improper operation of the circuitry,
and possible overstress of the laser source. Device deg-
radation or product failure may result.
Connection of the devices to a non-approved optical
source, operating above the recommended absolute
maximum conditions or operating the AFCT-5971LZ/
ALZ in a manner inconsistent with its design and func-
tion may result in hazardous radiation exposure and
may be considered an act of modifying or manufac-
turing a laser product. The person(s) performing such
an act is required by law to recertify and reidentify
the laser product under the provisions of U.S. 21 CFR
(Subchapter J).
Performance
Class 1 (>500 V).
Tested to 8 kV contact discharge.
Margins are dependent on customer board and chassis
designs.
Typically show no measurable effect from a
10 V/m field swept from 27 to 1000 MHz applied to the
transceiver without a chassis enclosure.
Accession Number: 9521220-133
License Number:
UL File Number: E173874
933/21203530/05
CC
.