AFCT-5971ALZ Avago Technologies US Inc., AFCT-5971ALZ Datasheet - Page 10

• Manufacturer Part Number: AFCT-5971ALZ
• Description: TXRX FE SM LASER 125MBS 2X5
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-5971ALZ

• Applications: Ethernet
• Data Rate: 125MBd
• Wavelength: 1300nm
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Data Rate Max: 0.125Gbps
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155Mbps
• Optical Rise Time: 2/2.2ns
• Optical Fall Time: 2/2.2ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1360/1580nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 3.1V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.5V
• Output Current: 50mA
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• Product: Transceiver
• Maximum Rise Time: 2 ns, 2.2 ns
• Maximum Fall Time: 2 ns, 2.2 ns
• Maximum Output Current: 50 mA
• Operating Supply Voltage: 3.1 V to 3.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: DIP-10 with Connector
• Function: Applications specified for signal rate of 125 MBd, for Fast Ethernet, and Singlemode Fiber.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Singlemode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Figure 8. Recommended Panel Mounting
10
DIMENSIONS IN MILLIMETERS (INCHES)
1.
2.
Recommended Solder and Wash Process
The AFCT-5971LZ/ALZ are compatible with industry-
standard wave solder processes.
Process plug
This transceiver is supplied with a process plug for
protection of the optical port within the LC connector
receptacle. This process plug prevents contamination
during wave solder and aqueous rinse as well as during
handling, shipping and storage. It is made of a high-
temperature, molded sealing material that can with-
stand +85°C and a rinse pressure of 110 lbs per square
inch.
The process plug should only be used once. After
removing it from the transceiver, it must not be used
again as a process plug; however, if it has not been
contaminated it can be reused as a dust cover.
Recommended Solder fluxes
Solder fluxes used with the AFCT-5971LZ/ALZ should
be water-soluble, organic fluxes. Recommended solder
fluxes include Lonco 3355-11 from London Chemical
West, Inc. of Burbank, CA, and 100 Flux from Alpha-
Metals of Jersey City, NJ.
(0.4 ±0.004)
10.16 ±0.1
FIGURE DESCRIBES THE RECOMMENDED FRONT PANEL OPENING FOR A LC OR SG SFF TRANSCEIVER.
SFF TRANSCEIVER PLACED AT 15.24 mm (0.6) MIN. SPACING.
(0.56 ±0.004)
14.22 ±0.1
DETAIL A
15.24
(0.6)
TOP OF PCB
15.24
(0.6)
B
(0.039)
(0.62 MAX. 0.59 MIN.)
15.75 MAX. 15.0 MIN.
1
A
SECTION B - B
SOLDER POSTS
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane
Other: naphtha.
Do not use partially halogenated hydrocarbons such as
1,1.1 trichloroethane, ketones such as MEK, acetone,
chloroform, ethyl acetate, methylene dichloride, phenol,
methylene chloride, or N-methylpyrolldone. Also, Avago
Technologies does not recommend the use of cleaners
that use halogenated hydrocarbons because of their
potential environmental harm.
LC SFF Cleaning Recommendations
In the event of contamination of the optical ports, the
recommended cleaning process is the use of forced
nitrogen. If contamination is thought to have remained,
the optical ports can be cleaned using a NTT interna-
tional Cletop stick type (diam. 1.25 mm) and HFE7100
cleaning fluid.
Regulatory Compliance
The Regulatory Compliance for transceiver performance
is shown in Table 1. The overall equipment design will
determine the certification level. The transceiver perfor-
mance is offered as a figure of merit to assist the design-
er in considering their use in equipment designs.
B