AFBR-5930Z Avago Technologies US Inc., AFBR-5930Z Datasheet - Page 8

• Manufacturer Part Number: AFBR-5930Z
• Description: TXRX SBCON 200MBD 2X5 DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of AFBR-5930Z

• Applications: General Purpose
• Data Rate: 200MBd
• Wavelength: 1300nm
• Voltage - Supply: 3.135 V ~ 3.465 V
• Connector Type: MTRJ
• Mounting Type: Through Hole
• Data Rate Max: 0.2Gbps
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Regulatory Compliance
Thes­e trans­ceiver products­ are intended to enable com-
mercial s­ys­tem des­igners­ to develop equipment that com-
plies­ with the various­ international regulations­ governing
certification of Information Technology Equipment. See
the Regulatory Compliance Table for details­. Additional
information is­ available from your Avago Technologies­
s­ales­ repres­entative.
Figure 6. Recommended Board Layout Hole Pattern
8
DIMENSIONS IN MILLIMETERS (INCHES)
NOTES:
1. THIS FIGURE DESCRIBES THE RECOMMENDED CIRCUIT BOARD LAYOUT FOR THE MT-RJ TRANSCEIVER PLACED
2. THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFFS. NO METAL TRACES OR
3. 10 PIN MODULE REQUIRES ONLY 16 PCB HOLES, INCLUDING 4 PACKAGE GROUNDING TAB HOLES CONNECTED
4. THE SOLDER POSTS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY AND TO
AT .550 SPACING.
GROUND CONNECTION IN KEEP-OUT AREAS.
TO SIGNAL GROUND.
ENSURE FOOTPRINT COMPATIBILITY WITH OTHER SFF TRANSCEIVERS.
(0.425)
(0.525)
13.34
10.8
KEEP OUT AREA
FOR PORT PLUG
(0.299)
(0.276)
7.59
7
(0.118)
3
(1.063)
27
(0.055 ±0.004)
Ø 1.4 ±0.1
(0.236)
(0.118)
6
3
(0.28)
7.11
(0.18)
4.57
17.78
(0.7)
(0.055 ±0.004)
Ø 1.4 ±0.1
(0.07)
1.778
(0.121)
Electrostatic Discharge (ESD)
There are two des­ign cas­es­ in which immunity to ESD
damage is­ important.
The firs­t cas­e is­ during handling of the trans­ceiver prior to
mounting it on the circuit board. It is­ important to us­e nor-
mal ESD handling precautions­ for ESD s­ens­itive devices­.
Thes­e pre-cautions­ include us­ing grounded wris­t s­traps­,
work benches­, and floor mats­ in ESD controlled areas­.
The s­econd cas­e to cons­ider is­ s­tatic dis­charges­ to the ex-
terior of the equipment chas­s­is­ containing the trans­ceiver
parts­. To the extent that the MT-RJ connector is­ expos­ed to
the outs­ide of the equipment chas­s­is­ it may be s­ubject to
whatever ESD s­ys­tem level tes­t criteria that the equipment
is­ intended to meet.
3.08
(0.28)
7.112
(0.121)
3.08
(0.14)
3.56
Ø 2.29
(0.09)
10.16
(0.4)
(0.378)
9.59
(0.032 ±0.004)
Ø 0.81 ±0.1
(0.55)
13.97
MIN.
Holes For
Housing
Leads
(0.079)
2
(0.055 ±0.004)
Ø 1.4 ±0.1