AFBR-5930Z Avago Technologies US Inc., AFBR-5930Z Datasheet
AFBR-5930Z
Specifications of AFBR-5930Z
Related parts for AFBR-5930Z
AFBR-5930Z Summary of contents
Page 1
... ECL referenced (shifted +3.3 V supply, into an analog LED drive current. Receiver Sections The receiver section of the AFBR-5930Z utilizes an InGaAs PIN photodiode coupled to a custom silicon transimped- ance preamplifier IC. It is packaged in the optical subassem- bly portion of the receiver. This ...
Page 2
Package The overall package concept for the Avago Technologies transceiver consists of three basic elements; the two op- tical subassemblies, an electrical subassembly, and the housing as illustrated in the block diagram in Figure 1. The package outline drawing and ...
Page 3
OVERALL RECEPTACLE CENTER LINE) 9.6 13.59 (0.378) (0.535) MAX. MAX. 7.59 (0.299) 8.6 (0.339) 12 (0.472) 9.3 9.8 (0.366) (0.386) MAX. MAX. Ø 1.07 (0.042) DIMENSIONS IN MILLIMETERS (INCHES) NOTES: 1. THIS PAGE DESCRIBES THE MAXIMUM ...
Page 4
RX TX Top View o RECEIVER SIGNAL GROUND RECEIVER POWER SUPPLY SIGNAL DETECT RECEIVER DATA OUT BAR RECEIVER DATA OUT 5 6 Figure 3. Pin Out Diagram. Pin ...
Page 5
Application Information The Applications Engineering group is available to assist you with the technical understanding and design trade- offs associated with these transceivers. You can contact them through your Avago Technologies sales representa- tive. The following information is provided to ...
Page 6
... Avago Technologies recommends that normal static pre- cautions be taken in the handling and assembly of these transceivers to prevent damage which may be induced by electrostatic discharge (ESD). The AFBR-5930Z series of transceivers meet MIL-STD-883C Method 3015. Class 2 products. ...
Page 7
Board Layout - Decoupling Circuit, Ground Planes and Termination Circuits It is important to take care in the layout of your circuit board to achieve optimum performance from these trans- ceivers. Figure provides a good example of a schematic ...
Page 8
Regulatory Compliance These transceiver products are intended to enable com- mercial system designers to develop equipment that com- plies with the various international regulations governing certification of Information Technology Equipment. See the Regulatory Compliance Table for details. Additional information is ...
Page 9
Regulatory Compliance Table Feature Test Method Electrostatic Discharge(ESD) to the MIL-STD-883C Electrical Pins Electrostatic Discharge Variation of (ESD) to the MT-RJ Recep- IEC 1000--2 tacle FCC Class B Electromagnetic Interfer- CENELEC CEN55022 ence (EMI) VCCI Class 2 Variation ofIEC 1000- ...
Page 10
... NOTE 15 AND 16 APPLY. Figure 9. Relative Input Optical Power vs. Eye Sampling Time Position. 10 Ordering Information The AFBR-5930Z 1300 nm product is available for produc- tion orders through the Avago Technologies Component Field Sales Offices and Authorized Distributors world wide. ...
Page 11
Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause catastrophic damage to the device. Limits apply to each parameter in isolation, all other parameters having values within the recommended operating conditions. It should not be assumed ...
Page 12
Transmitter Optical Characteristics (T = 0°C to +70° 3.135 V to 3.465 Parameter Output Optical Power BOL2.5/125 µ 0.25 Fiber EOL Optical Extinction Ratio Center Wavelength Spectral Width - FWHM Optical Rise Time ...
Page 13
Notes: 1. This is the maximum voltage that can be applied across the Differential Transmitter Data Inputs to prevent damage to the input ESD protection circuit. The outputs are terminated with 50 W connected The power ...
Page 14
For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright ...