AFBR-5805AZ Avago Technologies US Inc., AFBR-5805AZ Datasheet - Page 7

• Manufacturer Part Number: AFBR-5805AZ
• Description: TXRX ATM SONET OC3 3V SC 1X9
• Manufacturer: Avago Technologies US Inc.

Specifications of AFBR-5805AZ

• Applications: General Purpose
• Wavelength: 1310nm
• Voltage - Supply: 3.3V
• Connector Type: SC
• Mounting Type: Through Hole
• Data Rate Max: 0.1Gbps
• Supply Voltage: 5V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 100Mbps
• Optical Rise Time: 3/2.2ns
• Optical Fall Time: 3/2.2ns
• Jitter: 1.2/1.91ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1380nm
• Operating Supply Voltage (min): 3.135/4.75V
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 3.5/5.25V
• Output Current: 50mA
• Operating Temp Range: -10C to 85C
• Mounting: Through Hole
• Pin Count: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Rate: -
• Lead Free Status / Rohs Status: Compliant

Recommended Handling Precautions
Avago Technologies recommends that normal static pre-
cautions be taken in the handling and assembly of these
transceivers to prevent damage which may be induced
by electrostatic discharge (ESD). The AFBR-5800Z series
of transceivers meet MIL-STD-883C Method 3015.4 Class
2 products.
Care should be used to avoid shorting the receiver data
or signal detect outputs directly to ground without
proper current limiting impedance.
Solder and Wash Process Compatibility
The transceivers are delivered with protective process
plugs inserted into the duplex SC or duplex ST connec-
tor receptacle. This process plug protects the optical
subassemblies during wave solder and aqueous wash
processing and acts as a dust cover during shipping.
NOTES:
THE SPLIT-LOAD TERMINATIONS FOR ECL SIGNALS NEED TO BE LOCATED AT THE INPUT
R1 = R4 = R6 = R8 = R10 = 130 OHMS FOR +5.0 V OPERATION, 82 OHMS FOR +3.3 V OPERATION.
R2 = R3 = R5 = R7 = R9 = 82 OHMS FOR +5.0 V OPERATION, 130 OHMS FOR +3.3 V OPERATION.
C1 = C2 = C3 = C5 = C6 = 0.1 µF.
C4 = 10 µF.
L1 = L2 = 1 µH COIL OR FERRITE INDUCTOR.
Figure 7. Recommended Decoupling and Termination Circuits

TERMINATION
AT PHY
DEVICE
INPUTS
OF DEVICES RECEIVING THOSE ECL SIGNALS. RECOMMEND 4-LAYER PRINTED CIRCUIT
BOARD WITH 50 OHM MICROSTRIP SIGNAL PATHS BE USED.
NO INTERNAL CONNECTION
V
Rx
R6
EE
1
RD
R5
RD
2
V
CC
C6
RD
R7
RD
3
R8
Rx
SD
SD
4
AFBR-5805Z
TOP VIEW
R10
R9
C1
TRANSCEIVER
V
C3
AT V
Rx
V
CC
5
CC
L1
V
FILTER
CC
CC
PINS
NO INTERNAL CONNECTION
V
Tx
CC
C4
6
L2
Tx
C2
TD
7
TD
TERMINATION
AT TRANSCEIVER
INPUTS
R1
TD
R2
8
V
CC
V
Tx
C5
R3
EE
9
R4
TD
These transceivers are compatible with either industry
standard wave or hand solder processes.
Shipping Container
The transceiver is packaged in a shipping container de-
signed to protect it from mechanical and ESD damage
during shipment or storage.
Board Layout - Decoupling Circuit and Ground Planes
It is important to take care in the layout of your circuit
board to achieve optimum performance from these
transceivers. Figure  provides a good example of a
schematic for a power supply decoupling circuit that
works well with these parts. It is further recommended
that a contiguous ground plane be provided in the
circuit board directly under the transceiver to provide
a low inductance ground for signal return current. This
recommendation is in keeping with good high frequen-
cy board layout practices.