NHD-0416B1Z-FSPG-YBW-L-3V Newhaven Display, NHD-0416B1Z-FSPG-YBW-L-3V Datasheet - Page 21

• Manufacturer Part Number: NHD-0416B1Z-FSPG-YBW-L-3V
• Description: LCD MOD CHAR 4X16 Y/G TRANSFL
• Manufacturer: Newhaven Display
• Series: NHD-0416B1Z-Fr

Specifications of NHD-0416B1Z-FSPG-YBW-L-3V

• Display Type: STN - Super-Twisted Nematic
• Display Mode: Transflective
• Number Of Digits/alpha: 64
• Outline L X W X H: 87.00mm x 60.00mm x 14.00mm
• Viewing Area: 61.80mm L x 25.20mm W
• Backlight: LED - Green
• Display Format: 16 x 4
• Character Size: 4.75mm H x 2.95mm W
• Character Format: 5 x 8 Dots
• Voltage - Supply: 5.0V
• Dot Size: 0.55mm W x 0.55mm H
• Operating Temperature: -20°C ~ 70°C
• Character Count X Line: 16 x 4
• Module Size (w X H X T): 87 mm x 60 mm x 13.5 mm
• Features: Low Power Backlight
• Fluid Type: STN
• Background Color: Pure Green
• Voltage Rating: 3 V
• Operating Temperature Range: - 20 C to + 70 C
• Backlight Type: LED Yellow-Green
• Interface: Parallel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

NHD-0416B1Z
Soldering Precautions:
Operation Precautions:
Limited Warranty:
Newhaven Display LCDs and modules are not consumer products, but may be incorporated by
Newhaven Display customers into consumer products or components thereof, Newhaven Display does
not warrant that its LCDs and components are fit for any such particular purpose.
1. The viewing angle can be adjusted by varying the LCD driving voltage Vo.
2. Since applied DC voltage causes electro-chemical reactions, which deteriorate the display,
3. Driving voltage should be kept within specified range; excess voltage will shorten display
4. Response time increases with decrease in temperature.
5. Display color may be affected at temperatures above its operational range.
6. Keep the temperature within the specified range usage and storage. Excessive
7. For long-term storage over 40 C is required, relative humidity should be kept below 60%,
the applied pulse waveform should be a symmetric waveform such that no DC component
remains. Be sure to use the specified operating voltage.
life.
temperature and humidity could cause polarization degradation, polarizer peel-off or
generate bubbles.
and avoid direct sunlight.
1. The liability of Newhaven Display is limited to repair or replacement on the terms set forth
2. No warranty can be granted if any of the precautions stated in handling of liquid crystal display
3. When returning the LCD/LCM, they must be properly packaged and should have a detailed description of
3. Do not touch the connection terminals of the display with bare hand; it will cause
4. The modules should be kept in anti-static bags or other containers resistant to static
5. Only properly grounded soldering irons should be used.
6. If an electric screwdriver is used, it should be grounded and shielded to prevent
7. The normal static prevention measures should be observed for work clothes and
8. Since dry air is inductive to static, a relative humidity of 50-60% is recommended.
below. Newhaven Display will not be responsible for any subsequent or consequential events
or injury or damage to any personnel or user including third party personnel and/or user.
Unless otherwise agreed in writing between Newhaven Display and the customer, Newhaven
Display will only replace or repair any of its LCD which is found defective electrically or visually
when inspected in accordance with Newhaven Display general LCD inspection standard.
(Copies available on request)
above has been disregarded. Broken glass, scratches on polarizer mechanical damages as
well as defects that are caused accelerated environment tests are excluded from warranty.
the failures or defect
1. Soldering should be performed only on the I/O terminals.
2. Use soldering irons with proper grounding and no leakage.
3. Soldering temperature: 280 C+10 C
4. Soldering time: 3 to 4 second.
5. Use eutectic solder with resin flux filling.
6. If flux is used, the LCD surface should be protected to avoid spattering flux.
7. Flux residue should be removed.
disconnection or defective insulation of terminals.
for storage.
sparks.
working benches.
21
Newhaven Display